User manual CLIFFORD 50XUK

[. . . ] World-Class Auto Security TM concept 50x Owner's Manual n PLEASE NOTE: Your factory-set 4-digit valet code is noted below. See pages 10-11 for information on using your valet code: n If you wish to change your valet code to a different 4-digit number, please refer to the example on page 11. Write your new valet code in the space below: WARNING: For security reasons, do not keep this manual in your vehicle (since a thief could possibly access it and learn of your secret valet code). As such, please keep this manual in a safe place in your home. Concept 50x is covered by one or more of the following Clifford Electronics U. S. A. [. . . ] The next time that the ignition switch is turned to the "ON" position, valet mode is automatically exited. 11 Keyless entry in valet mode Even if valet mode is enabled, you can still remotely control the convenience features. For instance, press button 1 (channel 1) as if you were disarming: the doors will unlock (confirmed by one indicator light flash) and the interior lights will turn on. You can also use the other channels to activate options such as a remote boot release or remote engine starting. Sensor adjustment The two zones of your Concept 50x's Proximity Sensor provides dual-level protection of your vehicle. If someone is lurking near your car, perhaps bringing their hands and face to the window to see what is inside, the outer zone of the sensor will pick up this nearby movement and trigger your Concept 50x to issue its warning tone. But if a thief actually leans into the passenger compartment, the sensor's interior zone will be triggered and the system will instantly blast the full alarm sound. The Clifford Electronics Proximity Sensor is a radar-type sensor that uses a more sophisticated, more accurate and more reliable technology than that of ultrasonic-type movement sensors. As such, the Dual-Zone Proximity Sensor of your Concept 50x is impervious to normal environmental conditions such as wind and temperature variations that cause ultrasonic sensors to false alarm. Your Authorised Clifford Dealer will have adjusted each of the two sensor zones at the time of installation. If you find that the sensitivity setting of one or both appears to be a bit off the mark, any local Authorised Clifford Dealer will be happy to make any necessary readjustments without charge. Remote controlled override of one or both sensor zones Transmitting channel 10 (two presses of the side LevelShift button, then a press of button 2) within 10 seconds of arming the system will override the exterior warning zone of the Dual-Zone Proximity Sensor. When you do so, you will see 4 indicator light flashes to confirm the zone override. Transmitting channel 10 again within the 10 second period will override both zones of the sensor for those times when you must leave a passenger or pet in the vehicle. The sensor zones are automatically restored the next time you arm the system. AutoLock and AutoUnLock For your safety and that of your passengers, the doors automatically lock the instant you turn on the ignition (see User-selectable features on pages 16-20). When you turn the ignition off, AutoUnLock automatically unlocks the doors. To suit your preferences, you may turn off either or both the AutoLock and/or AutoUnLock features. 12 Built-In Two-Point AutoImmobiliser Thirty seconds after you turn off the ignition, the system's built-in two-point AutoImmobiliser electronically disengages your vehicle's starter motor and electronic fuel pump to ensure against theft of your vehicle. The LED Status Indicator will repeatedly flash to indicate that AutoImmobilisation has been activated. Even if a thief were to cut all the wires or even find the Concept 50x control unit and disconnect it, he would still be unable to start the engine. Please be aware that, unlike AutoArming described above, AutoImmobilisa tion occurs regardless of whether you open or close any doors. What's more, disabling the AutoArming feature has no effect on AutoImmobilisation. When you remotely disarm your Concept 50x, the AutoImmobilisation circuits automatically disengage. You then have 30 seconds to start the engine (or turn the ignition switch to its "ON" position). If more than 30 seconds pass, the immobiliser will automatically reactivate. [. . . ] Snap the case back together by first aligning the top (where the LED window is), then retightening (but not over-tightening) the retaining screw. Adding new remote controls For other drivers in your family, or if you wish to control Concept 50x systems on your other cars with the same remote control, you can buy additional remote controls from any Clifford Dealer (call our UK office on ring on 0800-929949 or 0181-646-8440 for the nearest dealers) and program them into the system yourself. Each Concept 50x will respond to as many as four 12-channel ACG remote controls. To add a new remote control to the system, use the procedures noted in the User-selectable features section on pages 16-20. [. . . ]