User manual CLIFFORD 50

[. . . ] World-Class Auto Security TM concept 50 Owner's Manual All Concept Series systems are covered by one or more of the following Clifford Electronics patents: 4, 158, 874; 4, 233, 642; 4, 327, 444; 4, 383, 242; 4, 430, 685; 4, 845, 464; 4, 887, 064; 4, 890, 108; 4, 922, 224; 4, 997, 053; 5, 081, 667; 5, 146, 215; 5, 157, 375 and other patents pending Table of Contents Standard Features of the Concept 50 . What to do in a carjacking situation . . . . . . . . . . . . . . . . . . . 7 8 8 8 8 8 Your 4-button/12-channel remote controls . 23 EXAMPLE 2: Turn off siren sound numbers 4 and 6, then turn on QuietChirps . 23 2 Standard Features of the Concept 5O Limited Lifetime Warranty -- Your system control unit and remote controls are covered for as long as you own your car (see warranty card for details). [. . . ] For instance, when having your car serviced, washed or parked by a valet. Remember: When your car will be driven by someone else (such as a mechanic) who will not know your disarming code, you must place Concept 50 in valet mode, otherwise your car will be immobilized. NOTE: If you temporarily lose the use of your remote controls, you can disarm the system by enabling valet mode. Turn the ignition switch to its "ON" position or start the engine. Enter your secret disarming code on the PlainView switch, then return the switch to its center position. You now have 3 seconds to flip the switch to the latched position (valet mode). Once you have enabled valet mode, the system's LED will glow continually for on-going visual confirmation of valet mode. Keyless entry in valet mode: Even if valet mode is enabled, you can still remotely control the convenience features. For instance, simply press button 1 (channel 1) as if you were disarming. The doors will unlock (as indicated by one flash of the parking lights) and the interior lights will illuminate. Press button 1 (channel 1) again and the doors will lock (indicated by two parking light flashes). You can also use the remote control's other channels to activate options such as a remote trunk release or remote engine starting. To exit valet mode 1. Turn the ignition switch to its "ON" position or start the engine (you may also perform the following while driving). The LED will turn off to confirm that the system is now in its normal operating mode. NOTE: You can even enable or exit valet mode with your remote control from outside the vehicle!See the Remote QuickAccess section on page 16. Dual-sensor protection Concept 50 system has two sensors: a Glass Tampering Sensor that detects attempts to break any of the vehicle's windows, and a Dual-Zone Magnetic Resonance Sensor that detects intrusion-related vibrations. What's more, the secondary, high-sensitivity zone of the Dual-Zone Magnetic Resonance Sensor can detect someone forcefully leaning against your vehicle's fender and will warn the person off with an unmistakable warning tone (instead of the full siren blast, which is reserved for a genuine intrusion attempt). 13 Remote controlled sensor testing and adjustment Because of ever-changing conditions, all alarms require periodic fine-tuning of the sensors. In fact, an improperly adjusted sensor is, by far, the biggest cause of false alarms. With other alarm brands, this requires repeated trips back to the dealer. You can adjust sensitivity without any tools and without even knowing where the sensor is mounted!If at any time you find the setting(s) of your system's sensors to be either too sensitive (i. e. , it tends to false alarm) or not quite sensitive enough, you may individually test and adjust the sensitivity settings yourself. To adjust the Glass Tampering Sensor or either zone of the Dual-Zone Magnetic Resonance Sensor, just use the following procedure: 1. Insert your car key and turn the ignition switch to its "ON" position, but do not start the engine. Enter your disarming code, then press and hold the switch to its spring-loaded momentary side for about 3 seconds until you hear a siren chirp. [. . . ] You will hear two chirps to indicate that that remote control button will now turn off the 20-second anti-carjacking countdown. Be sure to carry this remote on your person, since a carjacker will undoubtedly take your usual remote control and purse. NOTE 12: Immediately flip the switch to its latched position, then enter the new code that you wish to use. Make sure to return the switch to its center position when complete, then wait 3 seconds (you will hear two chirps when the system has accepted the new code). [. . . ]