User manual CLIFFORD 30

[. . . ] World-Class Auto Security TM concept 30 Owner's Manual World-Class Auto Security TM concept 30 Installation Manual Table of Contents Standard Features of the Concept 3O Welcome . . . . . . . . . . . . . . . . 18 2 Standard Features of the Concept 3O $3, OOO AntiTheft Guarantee -- Pays you up to $3, 000 if your vehicle is stolen and not recovered (see the AntiTheft guarantee card for details). Limited Lifetime Warranty -- Your system control unit and remote controls are covered for as long as you own your vehicle (see the warranty card for details). FACTTM -- False Alarm Control and Test -- Eliminates recurring false alarms. [. . . ] AutoArm & Lock: To ensure you can't accidentally lock your keys inside the car, the system is factory-set not to lock the doors upon AutoArming. To change this setting, see User-selectable features on pages 16­17. Instant AutoArming bypass: Prevents AutoArming when fueling the vehicle and other times when you wish to temporarily bypass AutoArming. To activate Instant AutoArming Bypass, rapidly turn the ignition switch to "ON" then "OFF. " You will hear a single siren chirp to confirm that the system will not AutoArm. The system reverts to its normal operating mode when you next start the engine. NOTE: To prevent AutoArming when fueling the vehicle, either use the Instant AutoArming Bypass feature noted above, or leave one of the doors open. 9 UltraSecureTM Coded Valet Mode Your secret valet code Within seconds, thieves can disable all other alarm brands by hot-wiring the ignition and flicking an easy to find "hidden" valet switch. Your Concept 30 has safeguards that absolutely ensure that a thief cannot enable the valet mode as a way of "turning off" your system. To enable valet mode, the driver must first enter a secret valet code on the PlainView switch. the code can be any number between 1 and 999, except those that contain a zero). Whenever the system is put in valet mode, all of the system's security features are switched off. For instance, when having your car serviced, washed or parked by a valet. NOTE: If you temporarily lose the use of your remote controls, you can disarm the system by enabling valet mode. Definitions Digit: A digit is defined as any number from 1 to 9, inclusive. Valet code: A valet code may be 1 to 3 digits: A one-digit code=X=any number between 1-9 A two-digit code=XY=any number between 11-99 (excluding numbers with zeros) A three-digit code=XYZ=any number between 111-999 (excluding numbers with zeros) Remember, no code can have a zero. A rocker switch mounted on the dashboard or console. The switch has three positions: 1. ) Latched 2. ) Center 3. ) Spring-loaded momentary. When you press the latched side, the switch remains in its pressed position. When you press the momentary side, the switch bounces back to the center position. Entering a digit: To enter a digit, you tap (press and release) on the momentary side of the PlainView switch the number of times corresponding to the numeral of the digit to be entered, followed by pressing to the latched side, then returning the switch to its center position. Entering a code: If your code has only one digit, enter the code as described in "Entering a digit, " then return the switch to its center position. If your code has more than one digit, just repeat the above for each digit of your code, then return the switch to its center position. PlainView switch: Currently, your factory-set valet code is the single digit "2. " 10 To enable valet mode 1. Turn the ignition switch to its "ON" position or start the engine. Enter your secret valet code, then return the switch to its center position. Once you have entered valet mode, the system's LED will glow continually for on-going visual confirmation of valet mode. Keyless entry in valet mode: Even if valet mode is enabled, you can still remotely control the convenience features. [. . . ] Siren duration: When the system detects an intrusion attempt, the alarm is set to sound for 30 seconds. SmartPowerUpTM If power is ever removed and restored in a theft attempt, SmartPowerUp automatically re-arms the system, sounds the siren, flashes the parking lights and electronically interrupts the starter. To disconnect power for servicing, simply insert your key into the ignition and turn it to the "ON" position before reconnecting power. Concept 30 recognizes this an an authorized power reconnection and will not alarm. 15 User-selectable features Your Concept 30 vehicle security system allows you to set many of its features to your own personal preferences. [. . . ]