User manual CLARION SR5000

[. . . ] Model SR5000 O Owner's Guide limited lifetime consumer warranty This Ungo Pro Security system is warranted against defects in material and workmanship. This Limited Lifetime Warranty applies to Ungo Pro Security systems that have been installed by an authorized Ungo Pro Security dealer. This warranty is to the Original Purchaser ("Owner") and to the original vehicle in which it was installed into. This warranty is not transferable to any subsequent owner(s) of the product(s). [. . . ] Be sure to check with your installer at the time of installation for both the location and the preset response (1-5 presses) of the override switch. Press the override switch the preset number of times (one to DRW-35 five times) within five seconds. If the system does not disarm, you may have waited too long; turn the ignition off and on and try again. Location of override switch_________________________________ Number of Presses_____________________________________ 25 important!The override switch can be programmed to respond to 1-5 presses for the disarm function. You must check with the installer to verify the programming for your individual unit. silent arm/disarm To temporarily turn off the arm or disarm chirps, use silent arm/disarm. Simply press for less than one second before arming or disarming, and the confirmation chirp(s) will be eliminated for that one operation only. When silent arm/disarm has been used the silent arm/disarm mode icon will indicate silent arm/disarm. If you want the arm/disarm chirps turned off permanently, your dealer can do this for you. note: The warning response to lighter impacts is bypassed if the system is armed using silent arm/disarm. This ensures that no chirps will be emitted by the siren in an area you want chirp-free. Only the warning response is bypassed. 26 panic mode If you are threatened in or near your vehicle, you can attract attention by triggering the system with your transceiver. To stop panic mode press note: Once panic mode has been entered, the siren will sound for 30 seconds. The transceiver will beep (or vibrate) continuously when the system enters panic mode. The transceiver will not generate a page notification when panic mode is exited. override mode You can prevent your security system from passive arming by using override mode. In override mode, the security system will not arm, even with the transceiver, but all convenience functions (door locks, trunk release, remote starting, etc. ) will continue to work normally. To enter or exit override mode: 1. Press and release the override switch within 10 seconds. DRW-35 27 The status LED will light solidly if you are entering override mode, and it will go out if you are exiting override mode. The transceiver will not generate a page notification when entering or exiting override mode using the override switch. To enter or exit override mode using the transceiver: 1. again. The status LED will light solidly if you are entering override mode, and it will go out if you are exiting override mode. The transceiver will generate alarm/disarm page notifications since the observing buttons are used when entering and exiting override mode. The status LED is the only way to ensure the system has entered/exited override mode. remote engine start This feature allows you to remotely start and run your vehicle for a programmable period of time. This makes it possible to warm up the engine, as well as adjust the interior temperature of the vehicle with the climate control system. If interior heating or cooling is desired, the climate controls must be preset, and the fan blower must be set to the desired level prior to remote starting the vehicle. 28 important!(1) Never remote start your vehicle when the keys are in the ignition, except when performing Override Take-Over, and (2) Never start the vehicle if it is not in either PARK or NEUTRAL. To remote start the vehicle: 1. Simultaneously press one second. and on the transceiver for 2. [. . . ] Any of these tones can be eliminated by the dealer, resulting in a unique, easily identifiable siren sound. The arm/disarm chirps can be either full volume or 6 decibels quieter than the full alarm blast. Using the Pro Security Programmer, the engine can be programmed to run for any duration ranging from 1 to 60 minutes. After the programmed run time, the engine will shut down and will not restart, unless in Timer Mode. [. . . ]