User manual CLARION MSS433

[. . . ] · Use extreme caution when drilling around electrical wiring, brake lines, and fuel lines. Check clearances on both sides of a planned installation surface before drilling any holes or installing any screws. · Always wear protective eyewear when using tools. · Use only high-quality RCA cables that are no longer than necessary for direct connections to other components in the system. [. . . ] MSS433 Chassis A/V Inputs, Outputs, & Power connectors. 9 SOURCE COMMANDER MSS433 DESCRIPTION OF MSS433 FRONT CONNECTORS BATT IGN (+12V) Reverse Wire 1 A/V Input Connections (Front Panel) 2 3 4 5 Figure 9. The MSS433's chassis input connectors. Adjust the input gain controls so that the source's level matches the audio level of the other video inputs. The MSS433 requires low-level signal inputs only. 1 A/V INPUT 1 (3 -RCA Jacks) Use a triple RCA A/V cable (not supplied) to connect video and stereo audio from the primary video source (e. g. , Clarion CVP9700 VCR, VS718 DVD Player, etc. ) to the MSS433 A/V Selector. See Applications on page 15. 2 A/V INPUT 2 (3 -RCA Jacks) Same as A/V Input 1. Use these jacks to connect a second video source (e. g. , video game console, etc. ) 10 OWNER'S MANUAL/INSTALLATION GUIDE 3 A/V INPUT 3 (3 -RCA Jacks) Same as A/V Input 1. Use these jacks to connect a third video source. 5 POWER INPUT CONNECTOR (4-Pin Molex) Connect the enclosed Molex pigtail to the vehicle's power, ground, and back-up light circuits, (see Figure 3 on page 6). 4 A/V INPUT 4 (3 -RCA Jacks) Same as A/V Input 1. NOTE: When using a optional Clarion Rear Vision Camera, the video connection must be connected to A/V Input 4 to function properly with the reverse wire. When +12Vdc is applied to the reverse wire (Pin 4), the MSS433 will automatically override Control Station 1's video selection and switch directly to A/V Input 4. The LED indicator will blink to show that the reverse function is active. The video signal will automatically override any other selection that is being viewed on Monitor 1. When voltage is removed from the reverse wire, the monitor will automatically switch back to the original source selected. 11 SOURCE COMMANDER MSS433 DESCRIPTION OF MSS43. REAR CONNECTORS (CONT'D) +- +- +- 6 7 8 9 0 q w e r Figure 10. The MSS433's A/V Outputs and Power connectors. 6 CONTROL STATION 1 (6 -Pin Connector) The Control Station connected to this port provides control and selection of Zone 1 audio/video sources. The Control Station connected to this port provides control and selection of Zone 3 audio/video sources. 9 A/V OUTPUT 1 (3 -RCA Jacks) Use this output when connecting the MSS433 to an external (PAL/NTSC-compatible type) video monitor for Zone 1. 7 CONTROL STATION 2 (6 -Pin Connector) The Control Station connected to this port provides control and selection of Zone 2 audio/video sources. 8 CONTROL STATION 3 (6 -Pin Connector) 12 0 MONITOR 1 OUTPUT (2 -Pin Connector) OWNER'S MANUAL/INSTALLATION GUIDE Connect to the monitor's +12 V and ground for Zone 1. DESCRIPTION OF CONTROL STATION q A/V OUTPUT 2 (3 -RCA Jacks) Use this output when connecting the MSS433 to an external video monitor for Zone 2. 1 w MONITOR 2 OUTPUT (2 -Pin Connector) Connect to the monitor's +12 V and ground for Zone 2. e A/V OUTPUT 3 (3 -RCA Jacks) Use this output when connecting the MSS433 to an external video monitor for Zone 3. 4 2 3 Figure 11. The Control Station's Power button, source LED indicators, and Source Select buttons. r MONITOR 3 OUTPUT (2 -Pin Connector) Connect to the monitor's +12 V and ground for Zone 3. 1 SOURCE SELECT LEDs When illuminated, each LED indicates which A/V source is selected. Press the SOURCE SELECT button to change source selection and the corresponding LED will illuminate. 13 SOURCE COMMANDER MSS433 2 SOURCE SELECT Button Press the SOURCE SELECT button one or more times to step through the different Audio/Video inputs. Press and hold the Power button for 2 to 3 seconds to power down the monitor at each of the Control Stations. 4 Mounting Bezel Outer mounting bezel around each Control Station allows for easy installation. (see page 6 for intallation information). 3 POWER Button When ignition is applied to the MSS433's ignition lead, all control stations are automatically set into the Stand-By mode (no power output from the monitor's power connector). Press the POWER button on any Control Station and the source LED will illuminate and the monitor will power on. [. . . ] At Control Station, press the POWER button once to turn on the Control Station. Connect Reverse wire on MSS433 to +12V source when vehicle shifted into reverse. No LED illumination on the Control Station. No Ignition power Station DIN not inserted fully into 6-pin connector. No sound from in-dash monitor CCA389 not connected properly. Camera not connected Connect a Clarion Rear Vision properly. [. . . ]