User manual CLARION DB285USB

[. . . ] Owner's manual Mode d'emploi Manual de instrucciones DB285USB CD/USB/MP3/WMA RECEIVER AUTORADIO CD/USB/MP3/WMA RECEPTOR CD/USB/MP3/WMA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] (Adjustment range: RIGHT12 to LEFT12 (right 12 to left 12)) Adjusting the fader 2-1. Turn the [ROTARY] knob to adjust the balance of the rear and front speakers. The factory default setting is "CENTER" (center). Press and hold the [SOUND] button for 1 second or longer to turn on the MAGNA BASS EXTEND effect. Press and hold the [SOUND] button for 1 second or longer to turn off the MAGNA BASS EXTEND effect. "M-B OFF" appears in the display for 2 seconds. 14 DB285USB Radio Operations English Listening to the radio 1. Each time the button is pressed, the radio reception band changes in the following order: F1 (FM1) F2 (FM2) F3 (FM3) AM F1 (FM1). . . Quick tuning Press and hold the [x] or [v] button for 1 second or longer to tune in a station. Step tuning Press the [x] or [v] button to manually tune in a station. Recalling a preset station A total of 24 preset positions (6-FM1, 6-FM2, 6FM3, 6-AM) exists to store individual radio stations in memory. Press the corresponding [DIRECT] button to recall the stored radio frequency automatically. Press the corresponding [DIRECT] button to recall the stored station. Note: · Press and hold one of the [DIRECT] buttons for 2 seconds or longer to store that station into preset memory. Tuning There are 3 types of tuning mode available, seek tuning, manual tuning and preset tuning. Seek tuning 1. Press the [BND] button and select the desired band (FM or AM). If "MANU" is lit in the display, press and hold the [BND] button for 1 second or longer. "MANU" in the display goes off and seek tuning is now available. Manual memory 1. Press and hold one of the [DIRECT] buttons for 2 seconds or longer to store the current station into preset memory. 2. When the [v] button is pressed, the station is sought in the direction of higher frequencies; if the [x] button is pressed, the station is sought in the direction of lower frequencies. Auto store Auto store is a function for storing up to 6 stations that are automatically tuned in sequentially. If 6 receivable stations cannot be received, a previously stored station remains unoverwritten at the memory position. The stations with good reception are stored automatically to the preset channels. Manual tuning There are 2 ways available: Quick tuning and step tuning. When you are in the step tuning mode, the frequency changes one step at a time. Press the [BND] button and select the desired band (FM or AM). If "MANU" is not lit in the display, press and hold the [BND] button for 1 second or longer. "MANU" is lit in the display and manual tuning is now available. 2. Tune into a station. DB285USB 15 Radio Operations English Preset scan Preset scan receives the stations stored in preset memory in order. This function is useful when searching for a desired station in memory. When a desired station is tuned in, press the [ ] button again to continue receiving that station. Note: · Be careful not to press and hold the [ ] button for 2 seconds or longer, otherwise the auto store function is engaged and the unit starts storing stations. Instant station recall (ISR) Instant station recall is a special radio preset that instantly accesses a favorite radio station at a touch of a button. [. . . ] Remove all wires attached to the power antenna excessive current is required lead. Check each wire for a possible short to for remote-on the amplifiers ground using an ohm meter. Reconnect each amplifier remote wire to the power antenna lead one by one. If the amplifiers turn off before all wires are attached, use an external relay to provide remote-on voltage (excessive current required). [. . . ]