User manual CLARION CC-2011E

[. . . ] 5 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Before installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Precautions when using two-sided tape for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · In the event it is necessary to drill holes in the vehicle for mounting, confirm that the drill bit or camera wiring will not strike or interfere with piping, gas tank, electrical wiring or other functional parts of the vehicle. · Do not rely solely on the monitor image when reversing the vehicle. The rear-view monitor is an auxiliary device meant for confirming the presence of obstacles to the rear of the vehicle, and is limited in its range. It should be used only in conjunction with direct visual observations. The rear-view monitor produces a wide-angle image, with the result that actual distances may be different than they subjectively appear in the monitor. · Do not use when the imaging surface or other parts are malfunctioning. · When installation and wiring are completed, confirm that the vehicle's horn, brake and warning lights, and other electrical equipment function properly as designed. CAUTION · Install only as directed in the Installation Manual. · When drilling holes in the vehicle for installation of wiring, always use insulated grommets in the holes to protect the wiring. · If holes are drilled in the vehicle to install the camera, or when installing wiring, use silicon sealant to seal any gaps. · After completing the camera wiring, use cable clamps or insulation tape to bundle the wiring together. · The images produced from the rear-view monitor are inverted right-left in the same way as images seen in the vehicle's rearview mirrors. · Do not use high-pressure car washing devices around the camera. The camera is a high-precision instrument and should not be subjected to high-pressure water stream impacts. · Periodically check the tightness of the installation screws and retighten if necessary. CC-2011E 3 3. SPECIFICATIONS Power source/voltage: Power consumption: Image sensor: Angle of view: Minimum subject illumination: SN ratio: Weight: Dimensions: DC 9 V (±0. 5 V) 120 mA or less 1/4" solid-state color CCD About 130° (horizontal) About 97° (vertical) 3 LUX or less (2 LUX ±1 LUX) 48 dB or more (AGC-OFF) About 72 g (bracket and 0. 5 m cable) 27 (W) × 25 (H) × 28. 3 (D) mm English Note: · Specifications and design are subject to change without notice for further improvement. Package contents 1 1 2 3 4 5 6 7 Camera (with 0. 5 m cable) . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning fluid (for use in preparing surface for 2-sided tape) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 1 1 4 2 1 7 3 1 2 3 4 5 6 8 9 7 0 4 CC-2011E 4. OPERATION Operation when using Clarion rear-view camera system The rear-view image is displayed when the transmission is placed into reverse, or when the manual switch is operated. English Troubleshooting The following symptoms are not malfunctions. Before having the unit serviced, check the following points once more. When using an independent power supply box, check the fuse and, if burned out, replace with a new one of the same capacity (1 A). If the fuse burns out repeatedly, consult your dealer or nearest Clarion Service Center. The image will return to normal when the light striking the lens is removed. [. . . ] · Within the first 24 hours after installation, do not expose the installation to moisture (water, rain, mist, snow, etc. ), or subject the installation to strong forces or impacts. · When installation must be performed under conditions of low ambient temperature (20°C or below), use a hair dryer to warm the surface of the bracket where the 2-sided tape is to be applied. · Do not touch the bracket-mounting surface's 2-sided tape, and do not attempt to move or reset the tape after initial application. 6 CC-2011E Installing/Wiring the camera English 2. Install mounting bracket A Using the supplied 2 installation screws (hex head M3 x 6), fasten bracket A to bracket B. [. . . ]