User manual CITIZEN VC-470TIV

[. . . ] Radio Signal Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Poor Reception Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Display during Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Confirming Reception Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] A confirmation tone will sound each time you press the upper right button (B) to start and stop the measurement. · RUN (run) is displayed in digital display 2 during measurement, and STP (stop) is displayed when the timer is stopped. Press the lower right button (A) during measurement to return to the initial set time and start measurement again. Press the lower right button (A) while the timer is stopped to return to the initial set time. When the time is up, END is displayed in digital display 2 and the time-up tone sounds for 5 seconds. · RES is displayed on digital display 2 and the timer returns to the initial set time. * The measurement continues even if the watch is switched to a different mode during measurement. * The time-up tone does not sound unless the crown is in the normal position. Button (B) Button (B) Measurement mark [Digital display 2] [Digital display 1] 56 57 W 17. Using the Chronograph (CHR) · The chronograph can display times up to 23 hours 59 minutes and 59. 99 seconds. · After it exceeds 24 hours, the chronograph returns automatically to the reset status. · While the chronograph is being operated, the display of digital display 2 changes as follows. (Reset) Button (B) (During measurement) <Using the chronograph> 1. Pull the crown out to position 1 and turn to align the mode hand with CHR (chronograph mode). · Digital display 2 goes off, digital display 1 enters the daylight saving time setting status for the city that is displayed, and ON or OF flashes. · The initial settings are all OF (canceled). [Digital display 1] 60 61 <Setting the desired time difference> · Any time difference can be set between the HOM city and the UTC time, in units of 15 minutes. (Range of -12 to +14 hours from UTC) · The radio wave received at HOM will be from the transmitter assigned to the city that has the most similar time difference with UTC. Pull the crown out to position 1 and turn to align the mode hand with WT-S (world time set mode). Pull the crown out to position 2 to enter the world time correction status. · ON or OF flashes and the watch enters the daylight saving time setting status. [Digital display 2] [Digital display 1] Daylight saving time ON/OF flashes Turn the crown to select HOM 4. Press the upper right button (B) twice to enter the time difference setting status. · Each time you press the upper right button (B), the "Daylight saving time ON/OF", "City display SET/OFF" and "Time difference setting" correction location changes. · Turn to the right to display (+) in the world time section and display time differences with UTC in 15-minute units in the time display section. · Turn to the left to display (­) in the world time section and display time differences with UTC in 15-minute units in the time display section. · Turn the crown continuously to change the time difference quickly. [. . . ] · Use a soft, dry cloth to wipe off perspiration and dirt from the leather band. · To clean a metal, plastic, or rubber watchband, wash away dirt with mild soap and water. Use a soft brush to remove dust and dirt jammed in the gaps in the metal band. NOTE: Avoid using solvents (thinner, benzine, etc. ), as they may damage the finish. CAUTION · Be sure to use the watch with the crown pressed in (normal position). [. . . ]