User manual CITIZEN SLD-7710

[. . . ] 7 Configuration (Block Diagram) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2. BASIC SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. 1 2. 2 2. 3 2. 4 2. 5 Printing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Printing Paper Specifications (Thermal Paper) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Black Mark Specifications (In case of M Type): Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Selecting memory switch Press the FEED switch short (within 0. 5 s) to select the memory switch to be set in the following order. However, when [5] is selected, the printer prints to verify the flash memory writing. [1] [2] [3] [4] [5] [6] [7] [8] [9] MSW1 MSW2 MSW3 MSW4 MSW5 MSW7 MSW9 MSW10 Write/Initializing setting 2) 3) Notes on operation · When [1] through [8] are selected, pressing the FEED switch long (2 s or more) causes the setting of the selected memory switch to be started. (Go to the following 4) Memory switch setting. ) · When [9] is selected, pressing the FEED switch long causes all current memory switch setting to be written into flash memory and the printer to be reset. (Go to the following 5) End of memory switch setting mode. ) · When [9] is selected, opening the platen and pressing and holding the FEED switch long causes current memory switch setting to be discarded and the factory set value to be recovered followed by reset operation. (Go to the following 5) End of memory switch setting mode. ) 4) Setting memory switch [1] Print the status of the bits currently being set. [2] Press the FEED switch short (within 0. 5 s) to reverse the bit selected. Then close the platen to print the status of current memory switch and return to 3) Selecting memory switch. Terminating memory switch setting mode When setting is completed, the contents of setting are saved and initialization (reset) occurs and the printer enters normal print-ready condition. 5) - 26 - PMU22XX/23XX Specifications 3. 4 Operation External Output The signals of LEDs and FEED switch can be output to the outside. 1) Pin 1 2 3 4 5 Pin assignment (CN301) Signal VCC FEED SW GND POWER LED ERROR LED Output Output Input Input/Output Function Circuit power supply (+5V) FEED switch input Circuit GND POWER LED output ERROR LED output Outer case POWER LED ERROR LED FEED SW 1 Main Board CN301 Connector used: 53014-0510 (Molex) 5 Figure Location of CN301 on Main Board CN301 is located on the Main Board. To access the Main Board, remove the screw holding the main board cover and slide the main board cover. However, no output is given when the printer is in the offline state even if the memory switch is set to OFF. full state. However, no output is given in the buffer - 30 - PMU22XX/23XX Specifications 2) Buffer full state Buffer full state is given when the remainder of the input buffer is in the following state. Table Set value 4K bytes 45 bytes Input Buffer Full Clear Remaining 512 bytes Remaining 26 bytes Buffer full Remaining 384bytes Remaining 16 bytes When the remainder of the input buffer is 0 byte, the received data is discarded. 3) Data receive error When any of the following error occurs, the data caused is printed with "?" or discarded. · Parity error · Flaming error · Overrun error (Msw1-4) Note When a command followed by Write FROM is used, the printer may possibly become DTR state temporarily at the time of writing. In this case, as the printer can process nothing, the transmitted data may be discarded. 4) Electrical characteristics RS-232C circuit (MAX232 or equivalent) Input (RD, DSR) [Printer side] [Host side] Output (DTR, TD) - 31 - PMU22XX/23XX Specifications 4. 2 Bidirectional Parallel Interface (IEEE1284) 4. 2. 1 Connector Pin Assignment (CN201) 10 1 20 11 Figure Connector for Parallel Connection Connector used: 53313-2065 (Monolex) Table Pin 1 2 3 4 5 6 7 8 9 10 Pin Assignment of Connector for Parallel Connection Signal nSTB DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 nACK Pin 11 12 13 14 15 16 17 18 19 20 Input/Output Output Output Output Input Input Output Input Signal BUSY PE SELECT nAUTOFD nRESET nFAULT nSELECTIN GND GND +5V Input Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Input/Output Output Input/Output 4. 2. 2 CN201 Connection to Parallel Port 36-pin Parallel interface CN201 25-pin Parallel interface Figure * Connection to 36-pin/25-pin Parallel Port When you want to connect to the connector other than the above, be careful not to make a mistake by confirming the status of each signal. - 32 - PMU22XX/23XX Specifications [2] [1] CN201 is located on the Main Board. To access the Main Board, remove the screw holding the main board Precautions · Before the work, remove the paper and unplug the interface and power connectors. · After wiring, fix the cable with a cable tie using the hole [2] to prevent the cable from being pulled from the outside. Wrong use may cause not only damage to the printer but also bad effect on human body, peripheral equipment, etc. 4. 2. 3 1) 2) 3) 4) Specifications of Supplied Cable for Parallel I/F Wiring Housing used: 51089-2005 Terminal used: 50212 (Molex) Cable used: AWG26 (UL1007) or equivalent Cable length: 300 mm (without cable-end treatment) - 33 - PMU22XX/23XX Specifications 4. 2. 4 1) Specifications Compatibility Mode (Host Printer communication: Centronics-compliant) [1] General Compatibility Mode specifies the Centronics interface widely used conventionally. [2] Specifications Data transmission system: Synchronization system: Handshake: Signal level: 8-bit parallel By nSTROBE signal supplied externally By nACK signal and BUSY signal All signals are TTL compatible. 2) Reverse Mode (Printer Host communication) Transmitting status data from this printer to the host is made by Nibble or Byte mode. [. . . ] 80 mm position 1: A little near 2: Standard 3: A little far PMU23X1 XXX 1L* (1: 102 mm L: Insert left *: Described above) 4: Far * The farther the paper position, the easier the paper insertion. PMU23X1 XXX 1R2 (1: 102 mm R: Insert right 2: Standard) PMU23X1 XXX 1T2 (1: 102 mm T: Insert top 2: Standard) New Head Open Mechanism - 63 - PMU22XX/23XX Specifications 8. 6 PMU23X2 Appearance Specifications (3-in. Mechanism-mounted Vertical Back Model) 1) 2) 3) Dimensions (mm): W113 × H213 × D98 Weight: Approx. 1. 1 kg External View - 64 - PMU22XX/23XX Specifications 4) Paper holder position: Paper diameter position 3 kinds x Front and back 4 kinds x Right and left 2 kinds + Upper 1 kind x Front and back 4 kinds = 28 kinds PNE position: Variable as desired Paper dia. 80 mm position PMU23X2 XXX 8L2 (8: 80 mm L: Insert left 2: Standard) 1: A little near 2: Standard 3: A little far PMU23X2 XXX 1L* (1: 102 mm L: Insert left *: Described above) 4: Far * The farther the paper position, the easier the paper insertion. [. . . ]