User manual CITIZEN SLD-7706

[. . . ] <m><t> 9 ESC FF Printing data in PAGE MODE P <1B>H<0C>H 10 ESC RS Buzzer-on S. P. <1B>H<1E>H 11 ESC SP Setting the right spacing of the character S. P. * <1B>H<20>H<n> 12 ESC !<1B>H<21>H<n> 13 ESC $ Specifying the absolute positions S. P. * <1B>H<24>H<n1> <n2> 14 ESC % Specifying/Canceling download character set S. P. <1B>H<25>H<n> <1B>H<26>H<s>H <n><m>[<a><p1> 15 ESC & Defining the download characters S. P. [. . . ] · Printer will reset its hard disk after finishing test printing. Therefore, the printer makes download characters, bit map images and macros undefined, clears the reception buffer/print buffer, and returns the various settings to defaults. · Printer will be BUSY when the processing of the command starts. -- 60 -- GS / m [Function] [Code] [Range] Printing the downloaded bit image <1D>H<2F>H<m> 0 48 [Outline] m m 3 51 Prints downloaded bit image in a mode specified by "m". Modes that can be selected by "m" are shown below. m 0, 48 1, 49 2, 50 3, 51 Dot Density in Vertical Direction NORMAL MODE 203 DPI DOUBLE WIDTH MODE 203 DPI DOUBLE HEIGHT MODE 101 DPI QUADRUPLE SIZE MODE 101 DPI Mode Name Dot Density in Horizontal Direction 203 DPI 101 DPI 203 DPI 101 DPI [Caution] · When data exist in the print buffer, this command is ignored. · When a downloaded bit image has not been defined, this command is ignored. · A portion of a downloaded bit image exceeding one line length is not printed. · A downloaded character and a downloaded bit image cannot be defined simultaneously. [See Also] GS * -- 61 -- GS : [Function] [Code] [Outline] Starting/Ending macro definition <1D>H<3A>H Specifying starting/ending macro definition. Reception of this command during macro definition signifies ending the macro definition. [Caution] Maximum content available for macro definition is 2048 bytes. · Even with ESC @ (Initialization of the printer) having been executed, defined content is not cleared. Therefore, it is possible to include ESC @ into the content of macro definition. Once defined, the left margin is not changed if the basic calculation pitch is changed by GS P. · The left margin is calculated with the horizontal basic calculation pitch (x) set by GS P. A fraction resulting from the calculation is corrected with the minimum pitch of the mechanism, and the remainder is omitted. · When mapping character data, if the print area specified is not wide enough to accommodate one character of the current font, only the line for that character data is handled as follows: (1) The print area is extended toward the right to be equivalent to one character of the current font, but not wider than the printable area. (2) If an area for one character cannot be provided as a result of step (1), the print area is extended toward the left. (So, the left margin is decreased. ) -- 67 -- · When mapping non-character data (Bit image, downloaded bit image, or bar code), if the print area specified is narrower than 9-bits, only the line for that data is handled as follows: (1) The print area is extended toward the left (So, the left margin is decreased) until it is 9-dot wide, but not wider than the printable area. [Default] [See Also] nL = 0, nH = 0 GS P, GS W -- 68 -- GS P x y [Function] [Code] [Range] [Outline] Specifying the basic calculation pitch <1D>H<50>H<x><y> 0 0 x y 255 255 This command sets the horizontal basic calculation pitch to approx. 25. 4/x mm (1/x inches), and the vertical basic calculation pitch to approx. · If x = 0, the horizontal basic calculation pitch is reverted to the default value. · If y = 0, the vertical basic calculation pitch is reverted to the default value. [Caution] · The horizontal direction is defined as the direction perpendicular to the paper feed, and the vertical direction is defined as the paper feed direction. · In STANDARD MODE, the following parameters are used regardless of the character orientation (e. g. [. . . ] · In calculating a correction span, use the calculated basic feed span for the vertical direction. The fractional part contained in the calculation result should be used for correction at an increment of the mechanism's minimum feed span, with the remaining fractional part truncated. FF, GS FF -- 105 -- GS C0 m n [Function] [Code] [Range] [Outline] Setting the numbering print mode. <1D>H<43>H<30>H<m><n> 0 0 m n 5 2 This command sets the numbering(serial number counter) print mode. [. . . ]