User manual CITIZEN PRODOT 350

[. . . ] PROdot 350 User's Manual Addendum -1- Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Trademark Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Chapter 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Overview of Additional Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The end of the flexible cord should be suitably prepared and the correct plug fitted. The wires in this mains cord are coloured in accordance with the following code:Green/Yellow = Earth, Blue = Neutral, Brown = Live. As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:The wire which is coloured Green/Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured Green or Green/Yellow. The wire which is coloured Blue must be connected to the terminal which is marked with a letter N or coloured Black or Blue. The wire which is coloured Brown must be connected to the terminal which is market with the letter L or coloured Brown or Red. Important: This appliance must be earthed -6- Chapter 1 Overview of Additional Features Thank you for purchasing this Citizen Prodot 350 printer. This user manual addendum should be used in conjunction with the Prodot 300 user manual also supplied with this printer to provide a full list of the features and functions within this printer. Automatic Media Thickness Selection The integral sensors within the printer's printhead mechanism detect the thickness of the media being used and adjust the printhead height to the correct level for printing. This makes it ideal for multi-thickness media or for items such as passbooks where the printer must automatically select the thickness depending on the page of the book being used. Automatic Media Straightening If media is miss-inserted in to the front of the printer at an incorrect angle, the Prodot 350 will automatically correct the angle of the media to ensure it is straight within the printer. Left Edge Detection The printer can automatically detect the left edge of the media if it is inserted incorrectly. This is also a great feature if the printer is being used in automatic media straightening mode as this feature can naturally move the media left or right whilst straightening. Automatic Media Selection The printer can automatically switch between tractor media and cut sheet media using software control commands making it ideal for banking or retail situations. The function also exists to park the paper on the tractors when printing is finished. -7- Chapter 2 Installation Unpacking Check each of the items against the following packing list. If any of these items are missing, please contact the dealer from whom you purchased the printer. A B C D E Printer Driver Disk User Manuals (including this one) Ribbon cassette Printer Power Cord Hold the bottom of printer in the box, and then care fully lift it up. They are specially designed to protect the printer and will make re-packing easy. -8- Before Using Your New Printer Before using your new printer, please remove the five shipping pads from the printer. Press the ONLINE and PARK/LOAD keys for 3 seconds so that the printhead moves several times to the left end of the carriage to ensure the ribbon slips in to the ribbon guides. Having installed the ribbon, lower the front roller unit and close the top cover. - 12 - Chapter 3 Loading Media In To The Printer Paper Thickness Adjustment By default, the Prodot 350 printer will detect the thickness of media being used on the first line of each page. You can override the default settings using the control panel and the printer's configuration settings. Details of the method of adjusting the configuration settings can be found in Chapter 5 of this manual and in the Prodot 300 manual. Then press the PARK/LOAD key to set the paper select lever at the cut-sheet position as shown in the figure below. [. . . ] Press the ONLINE key and the length will be stored in the printers memory. Its length will be valid until another passbook is measured. Passbook2 Mode - Fixed passbook length In Passbook2 mode, the length of the passbook is determined by the menu setting called PB Length. Using a fixed length passbook setting will be quicker as the printer does not have to check and determine the length of the passbook before printing starts. Calculation of PB Length for Passbook2 mode. First determine the size of one leaf of the passbook, as shown in the diagram. [. . . ]