User manual CITIZEN PRODOT 300

[. . . ] 7 Automatic Media Thickness Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Automatic Media Straightening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Left Edge Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Automatic Media Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please ensure that the socket outlet is installed near the equipment and shall be easily accessible. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the -5- operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. If the product exhibits a distinct change in performance, indicating a need for service. 14. The power cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS1362 fuse must be used of the same rating, marked thus. If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i. e. Fuse covers are available from the Parts Department indicated in your user instructions. If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed. Open the top cover and then pull the front roller unit by gripping the centre area of the unit by your forefingers until you hear a click. Then lift it - 11 - up until the unit is positioned on the top of printer as shown above. Hold the ribbon cartridge with the knob facing upwards and turn the ribbon knob in the direction shown by the arrow to take up any slack in the ribbon. 5. To install the ribbon cartridge, hold it with both hands, with the ribbon facing down as shown in the figure. When you look at the print head you will find a small piece of black plastic on the thin metal sheet of the ribbon guide. Position the ribbon cartridge with the tabs on its case over the slots inside the printer case. Open the tractor paper guide and place the paper on the sprocket pins as shown. If you are using pre-printed paper or labels, install them with the printed or labelled side facing upwards Release the lock lever of the right tractor and open the tractor paper guide. Slide the right tractor to left to take up any slack in the paper, then fasten the lock lever to fix the tractor in position as shown. If the paper is not aligned with the print start position, release the tractor lock levers of the left and right tractors, align the paper, and then fasten the lock lever to lock the tractors. To tear off the paper, make sure that printed paper is fed to the front table. [. . . ] This selects the fixed heap gap value when using the "Fix Pos" Head Gap. This sets the fixed passbook length in values from 2 inches to 4 inches, in one-sixth inch increments. When enabled, causes the printer to increase the heap gap to the maximum value while the printer skips over the perforations between continuous paper sheets. Gap Pos. PB Length Cross Page Skew Correct Enables or disables the shutter mechanism operation for straightening media not correctly inserted. - 23 - Passbook1 Mode - Automatic Passbook Length Detection In off-line mode, press and hold the PARK/LOAD and DRAFT/LQ keys for about 3 seconds to enter automatic passbook measurement mode. Insert a passbook into the printer so that the passbook is automatically is fed to the measure the length of the passbook. [. . . ]