User manual CITIZEN PRINTIVA QUICK GUIDE

[. . . ] It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference. This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus, as set out in the radio interference regulations of the Canadian department of communications. After having read this manual, keep it in a safe, readily accessible place for future reference. [. . . ] Character type User memory Bar code types Line spacing Paper roll 4 mm/outer 32 mm) Interface Serial (RS-232C compliant), parallel (IEEE 1284 compliant), USB, USB with hub, Ethernet, Powered USB Cash drawer kick-out Supports 2 cash drawers Buffer size 4 k bytes/45 bytes Supply voltage DC 24 V ±5% Power consumption Approximately 45 W (normal printing), 3 W (standby) Rated input: AC 100 to 240 V, 50/60 Hz, 150 VA AC adapter *4 (36AD2, 36AD3) Rated output: DC 24 V, 2. 5 kg Outside dimensions PRINTIVAS: 145 (W) × 192 (D) × 142 (H) mm PRINTIVAA: 145 (W) × 192 (D) × 114 (H) mm Operating temperature 5 to 45°C, 10 to 90% RH (no condensation) and humidity Storage temperature -20 to 60°C, 10 to 90% RH (no condensation) and humidity Reliability Print head life: 150 km, 200 million pulses (at normal temperature/humidity, using recommended paper and paper thickness) Auto cutter life: 2 million cuts (full cut), 1. 6 million cuts (partial cut) (at normal temperature/humidity, using recommended paper and paper thickness) UL, C-UL, FCC Class A, TÜV-Bauart, CE Marking Safety standard *5 *2: The number of printable columns is selected using a memory switch. *3: Characters appear small because the dimensions include a blank area surrounding each character. Names of parts Front cover release button Paper cover Open to load paper. 3 Clearing a Cutter Lock (2) Front cover release button Press this button to open the front cover. POWER LED (green) Lights when the power is on, turns off when the power is off. Memory switch Setting of various kinds of functions can be stored in memory. Settings remain stored in the memory even if the printer is turned off. For the built-in power type printer, connect the AC power cord to the AC inlet, and insert the plug into an electric outlet. for the AC adapter type printer , connect the cable connector of the AC adapter to the power connector. Press in the position shown by the arrow and set the partition in a slot that matches the width of the paper roll you are using. Or, when you are using a 60-mm wide paper roll with the 2inch type, remove the partition installed for 58-mm. Make sure the partition is not slanted when setting it for 58-mm or 60-mm paper rolls. Turn off the printer and unplug the power cord from the electric outlet. When setting the DIP switch, do not remove any screws except the serial interface board mounting screws. 1 2 3 4 5 6 7 8 Function Communication condition setting Hand shake Bit length Parity check Parity selection Baud rate selection INIT Reset ON According to DIP switch settings XON/XOFF 7 bits Yes Even parity Refer to table below. 1 is set to OFF, you can use a command or a memory switch to select 1200, 38400, 57600, or 115200 bps. Change the settings of the paper near-end sensor to set the position at which the near-end of the paper is detected. Use a pointed object, such as a pen, to gently press the button to change the paper near-end sensor. Press and hold down the button while moving the paper near-end sensor up and down. The sensor positions are shown below for the various diameters of the paper roll used. [. . . ] The memory switches can be set manually (set by hand on the printer) or by commands. For information on how to set the memory switches using commands, please refer to the Command Reference. Quick setting mode The settings for the memory switches for a replacement printer's manufacturer, model, paper width, and character spacing can be set at the same time to the optimum settings. While the paper cover is open, press and hold the FEED button while turning the power on. [. . . ]