User manual CITIZEN PN60I

[. . . ] ·Do not place this product on an unstable cart, stand or table. ·Slots and openings on the back or bottom of the case are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. The openings should never be blocked by placing the product on a bed, sofa, rug of other similar surface. [. . . ] Therefore, it is possible to include ESC @ into the content of macro definition. ·Normal printing operation is carried out even while in macro definition. GS ^ [Print Results] LPRINT CHR$ (&H1D) + " : " ; LPRINT "+ - - - +" + CHR$ (&HA) ; LPRINT "| |" + CHR$ (&HA) ; LPRINT "+ - - - +" + CHR$ (&HA) ; LPRINT CHR$ (&H1D) + " : " ; LPRINT CHR$ (&H1D) + " ^ " ; LPRINT CHR$ (2) + CHR$ (10) ; LPRINT CHR$ (0) ; END [Sample Program] GS B n Specifying/Canceling the black/white inverted printing <1D>H<42>H<n> 0 £ n £ 255 This command specifies or cancels the black/white inverted printing. ·If n = <*******0>B, the black/white inverted printing is canceled. ·If n = <*******1>B, the black/white inverted printing is specified. [Function] [Code] [Range] [Outline] [Caution] ·Number "n" is only valid in the lowest bit. ·The black/white inversion works on internal and downloaded characters. ·The black/white inversion works also on the right spacing of characters defined by ESP SP. ·This command does not affect the bit image, downloaded bit image, bar code, HRI characters, or the skip area specified by HT, ESC $, or ESC ¥. · Black/white inversion specification take precedence over underline specification. Underline printing due to underline specification is, therefore, nullified if black/white inversion is specified; the underline setting, however, remains unchanged. [Default] n=0 GS H n Selecting of printing position of HRI characters <1D>H<48>H<n> 0£n£3 48 £ n £ 51 Selecting printing position of HRI characters in printing bar codes. n 0, 48 1, 49 2, 50 3, 51 Printing Position No printing Above the bar code Below the bar code Both above and below the bar code [Function] [Code] [Range] [Outline] [Caution] · The HRI characters refer to the bar code-turned characters so that you can read them. ·Commands using x: ·Commands using y: ESC SP, ESC $, ESC W, ESC ¥ ESC 3, ESC J, ESC W, GC S, GS ¥ (2) If the start point specified by ESC T is the top right or bottom left (the characters are mapped in the paper feed direction). ·Commands using x: ·Commands using y: ESC 3, ESC J, ESC W, GC S, GS ¥ ESC SP, ESC $, ESC W, ESC ¥ ·This command does not affect any other values that are already set. ·If calculations made for a combination with another command generate fractions, the fractions are corrected with the minimum pitch of the mechanism, and the remainder is omitted. [Default] [See Also] x = 180, y = 360 "Page Mode" in Appendix 1 ESC SP, ESC $, ESC 3, ESC J, ESC W, ESC ¥, GS $, GS L, GS W, GS ¥ GS GS V V m . . . . . . . . . (2) Cutting the paper (1) (2) (1) (2) <1D>H<56>H<m> <1D>H<56>H<m><n> 0 £ m £ 1, 48 £ m £ 49 65 £ m £ 66, 0 £ n £ 255 [Function] [Code] [Range] [Outline] Cuts the specified paper. m 0, 48 1, 49 65 66 Meaning Full cut Partial cut (leaving a bridge area uncut) Paper feed by "cut position + {n´basic calculation pitch}´and full cut Paper feed by "cut position + {n´basic calculation pitch}´and partial cut (leaving a bridge area uncut) [Caution] ·In Standard mode, this command only works when it is entered at the beginning of a line. For (1): ·A partial cut (leaving a bridge area uncut) is executed. For (2): ·If n = 0, the paper is fed to the cut position, and then cut. If n¹0, the paper is fed by "n´basic calculation pitch" inches past the cut position, and then cut. The paper feed amount is calculated with the vertical basic calculation pitch (y). A fraction resulting from the calculation is corrected with the minimum pitch of the mechanism, and the remainder is omitted. GS W nL nH [Function] [Code] [Range] [Outline] Setting the print area width <1D>H<57>H<nL><nH> 0 £ nL £ 255 0 £ nH £ 255 Sets the print area width specified by nL and nH. [. . . ] 9) Nach der Übertragung eines Datenbytes signalisiert der Drucker dem Host-Computer, ob weitere Daten zur Übertragung vorliegen. Wenn der Host-Computer feststellt, daß keine weiteren Daten vom Drucker kommen, wählt der Host-Computer einen der folgenden drei Stati: 1. Durchführung der Terminierung und Rückkehr in den Kompatibilitätsmodus 2. Setzen von HostBusy (nAutoFd) auf Low und Wechsel in die Phase "Reverse Idle" (Event 7) 10) Wenn der Drucker weitere Daten senden will, wählt der Host-Computer einen der folgenden drei Stati: 1. [. . . ]