User manual CITIZEN PN60

[. . . ] 1 1. 3. 1 Control Command Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 3. 2 How to Send Control Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONTROL COMMANDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. 1 ESC/POS Command List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 00 00 00 04 00 08 01 00 20 00 40 00 Decimal 0 0 0 4 0 8 16 0 32 0 64 0 (2) 2nd byte (Error occurrence information) Bit 0 1 2 Status Undefined Undefined No B. M detection error occurred (only when B. M paper is selected). Auto cutter error not occurred Auto cutter error occurred Unused Unrecoverable error not occurred Unrecoverable error occurred Auto recovery error not occurred Auto recovery error occurred Unused Hex. -- -- 00 04 00 08 00 00 20 00 40 00 Decimal -- -- 0 4 0 8 0 0 32 0 64 0 3 4 5 6 7 (3) 3rd byte (Paper Sensor information) Bit 0, 1 2, 3 4 5 6 7 Status Paper found by Paper Near-end Sensor Paper not found by Paper Near-end Sensor Paper found by Paper-end Sensor Paper not found by Paper-end Sensor Unused Undefined Undefined Unused Hex. 00 03 00 0C 00 -- -- 00 Decimal 0 3 0 12 0 -- -- 0 -- 56 -- (4) 4th byte (Paper Sensor information) Bit 0 1 2 3 4 5 6 7 Status Undefined Undefined Undefined Undefined Unused Undefined Undefined Unused Hex. -- -- -- -- 00 -- -- 00 Decimal -- -- -- -- 0 -- -- 0 * In case of MSW3-7 ON (CBM1000 compatible mode) (4) 4th byte (Paper Sensor information) Bit 0 1 2 3 4 5 6 7 Status Reserved Reserved Reserved Reserved Fixed Reserved Reserved Fixed Hex. 01 02 04 08 00 00 00 00 Decimal 1 2 4 8 0 00 00 0 * In case of MSW3-7 OFF (CBM1000 non-compatible mode) [Default] When MSW 1-3 OFF: n = 0 When MSW 1-3 ON: n = 2 DLE EOT, GS r [See Also] -- 57 -- GS r n [Function] [Code] [Range] Sending status <1D>H<72>H<n> 1n2 49 n 50 Sends the specified status to the host. Sends the Drawer Kick-out Connector status. [Outline] · When the serial interface is used: For DTR/DSR control: The printer sends the status after verifying that the host is ready to receive. If the host is not ready to receive, the printer waits for the host to become ready to receive. For XON/XOFF control: The printer sends the status without checking whether the host is ready to receive or busy. · Because this command is executed when data is mapped in the receive buffer, there may be a delay between receiving the command and sending the status depending on the condition of the receive buffer. · If ASB (Automatic Status Back) is enabled by GS a, the host must discriminate between the status due to this command and the status due to ASB. · While in macro execution with n3 = 1, paper feed with the FEED switch is not available. GS : Refer to Sample Program and Print Results for GS:. [Caution] [See Also] [Sample Program] -- 64 -- 2. 2. 10 Cutter Commands GS V m . . . . . . . . . (2) [Function] [Code] Cutting the paper (1) <1D>H<56>H<m> (2) <1D>H<56>H<m><n> (1) m = 1, m = 49 (2) m = 66 Performs the specified paper cutting. m 0, 48 1, 49 65 66 [Caution] Function Full cut Partial cut (Leaving a bridge area uncut) Paper feed by "cut position + {n × basic calculation pitch}" and partial cut Paper feed by "cut position + {n × basic calculation pitch}" and partial cut [Range] [Outline] · In STANDARD MODE, this command only works when it is entered at the beginning of a line. · Control to make the length of cut paper less than 10 mm is not excecuted. For (2): · If n = 0, the paper is fed to the cut position, and then cut. If n 0, the paper is fed by "n × basic calculation pitch" inches past the cut position, and then cut. The paper feed amount is calculated with the vertical basic calculation pitch (y). A fraction resulting from the calculation is corrected with the minimum pitch of the mechanism, and the remainder is omitted. -- 65 -- 2. 2. 11 Bar Code Commands GS H n [Function] [Code] [Range] Selecting of printing position of HRI characters <1D>H<48>H<n> 0n3 48 n 51 Selecting printing position of HRI characters in printing bar codes. n 0, 48 1, 49 2, 50 3, 51 Printing Position No printing Above the bar code Below the bar code Both above and below the bar code [Outline] The HRI characters refer to the bar code-turned characters so that you can read them. [Caution] · The HRI characters are printed in the font selected with GS f. [. . . ] This is indicated by setting HostClk (nStrobe) to Low (Event 16) and then to High. (Event 17) Events 10 and 16 may occur simultaneously, and Events 7 and 17 may occur simultaneously. (Such as when HostBusy and HostClk are used together. ) After transferring one byte of data, the printer signals to the host whether it has more data to transfer. When there is no more data to be received by the host from the printer, the host chooses one of three status selections: 1. [. . . ]