User manual CITIZEN PD-04

[. . . ] 5 Included and Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Included Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 External Appearance and Part Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Do not use any batteries other than AA rechargeable NiMH batteries, AA rechargeable NiCd batteries, and AA alkaline batteries. · Always use four identical batteries at the same time. 7 7 Precautions when using rechargeable batteries Danger · If the fluid of a rechargeable battery gets in your eyes, you will be in danger of being blinded, so immediately wash them with clean water without rubbing them and promptly go to a doctor for treatment · The plus and minus directions of rechargeable batteries are preset. When placing batteries in the printer, check the plus and minus directions. · If you do not obey the following instructions, the rechargeable battery will leak, overheat, or crack. ­ Do not touch their plus and minus terminals with a wire or other metal object. If a rechargeable battery is taken apart or modified, it will leak, overheat, or crack. Warning · If fluid from a rechargeable battery touches your skin or clothing, there is a danger of it harming your skin, so wash it off with clean water immediately. 8 Safety Instructions Precaution · Do not touch or moisten rechargeable batteries with fresh water or seawater. If a rechargeable battery is used or left in a hot place, it will leak, reducing its performance and service life. · Store rechargeable batteries where they are out of the reach of infants and small children. Be extremely careful that an infant or small child does not take out the rechargeable batteries. · Use a charger that matches the specifications of each type of battery. · Be sure to fully charge new rechargeable batteries before using them for the first time. PD79901-0S) Roll Paper (30 mm x 10 m) AC Adapter Battery Adapter Battery Adapter Cover Installation Guide AC Adapter Kit (Part No. PD69957-0S) 12 External Appearance and Part Descriptions 8 9 0 1 2 5 7 4 1 POWER LED (POWER: Green) The green indicator lights when the power is on. Additionally, the indicator blinks according to the printer mode (refer to the Error Indication Table). Once the black mark is detected, you can then feed the paper as needed with more accurate detection of the point where the paper is to be cut. # Print Thermal Head This is the actual printing component. Printer Underside $ $ Battery Cover Remove the cover to load the batteries (see p. 16). % Battery Release Strip % 15 About the Power Source The printer only runs on four AA rechargeable or dry cell batteries. This section explains how the batteries are loaded and provides additional information about the batteries. Loading the Batteries Have on hand the four AA alkaline batteries provided with the printer. (Follow the same sequence of steps when replacing the batteries. ) 1 2 Slide the battery cover downwards to open the cover. Place the batteries in the compartment with each battery's "+" and "­" terminal oriented as shown in the figure. · When replacing batteries, first remove the four batteries loaded in the printer. 1 3 2 Slide the battery cover up again to close. Use These Batteries 7 You can use the following batteries with this product. · AA rechargeable NiMH batteries (Recommended) · AA rechargeable NiCd batteries · AA alkaline batteries 7 Do not use any batteries other than those listed above. Use of batteries other than those specified may result in damage to the unit. [. . . ] When the POWER LED and the ERROR LED are blinking together, release the POWER button ( ). When the POWER LED and the ERROR LED begin to blink alternately, release the FEED button. Press the FEED button to begin the selfprint test. · To repeat the test, press the FEED button again after the previous test is completed. 23 Printing Test Hex Dump Function 1 2 3 With the paper loaded, simultaneously hold down the POWER button ( ) and FEED button. When the POWER LED and the ERROR LED are blinking together, release the POWER button ( ). [. . . ]