User manual CITIZEN MT-854A

[. . . ] The openings should never be blocked by placing the product on a bed, sofa, rug of other similar surface. This product should never be placed near or over a radiator or heater. This product should not be placed in an built-in installation unless proper ventilation is provided. ·This product should be operated from the type of power source indicated on the marking label. [. . . ] (See a download bit image printout. ) dots is represented by n2 ´ 8, respectively. 0 £ n2 £ 24 Note) Take care that the number of data (n1´n2´8) is equal to or smaller than Once the download bit image is defined, it remains valid until it is redefined or the download deletion command (ESC DC2 n1 n2) is executed. 72 CITIZEN iDP-3420/3421/3423 User's Manual GS ¤ m [Function] [Code] [Range] [Outline] [Caution] Printing the download, bit image <1D>H <2F>H m 0 £ m £ 255 This command prints the bit image saved in the number specified with m. If the bit image has not been saved in the specified number, this command will be ignored. 73 CITIZEN iDP-3420/3421/3423 User's Manual 13. 13. 2 STAR Mode Command ESC R n ESC 6 ESC 7 ESC M ESC P ESC : SO DC4 ESC E ESC F ESC ESC _ ESC 4 ESC 5 SI DC2 LF CR ESC z ESC 0 ESC a n FF ESC C n ESC C 0 n VT ESC B n1 n2 ESC N n ESC 0 ESC 1 n ESC Q [n] k NUL HT ESC D n1 n2 ESC 1 ESC A n ESC 2 ESC J n ESC K n1 <0> ESC L n1 n2 ESC h n ESC & <0> n1 n2 Function Selecting the international character set NOP NOP NOP NOP NOP Specifying the double width character Canceling the double width character Specifying the highlight character Canceling the highlight character Specifying/Canceling the underline NOP Specifying the red print Canceling the red print Specifying the inverted character Canceling the inverted character Printing and paper feed Printing Setting the 1/6-inch line feed NOP n-line paper feed Form feed (Change the page) Setting the n-line page length Setting the n-inch page length Vertical tab Setting the vertical tab position Setting the lower margin Canceling the lower margin Setting the left margin Setting the right margin Horizontal tab Setting the horizontal tab position Setting the 1/9-inch line feed width NOP Setting the 2/9-inch line feed width NOP Code 1BH 52H n 1BH 36H 1BH 37H 1BH 4DH 1BH 50H 1BH 3AH 0EH 14H 1BH 45H 1BH 46H 1BH 2DH n 1BH 5FH n 1BH 34H 1BH 35H 0FH 12H 0AH 0DH 1BH 7AH 1BH 30H 1BH 61H n 0CH 1BH 43H n 1BH 43H 00 n 0BH 1BH 42H n1 n2 1BH 4EH n 1BH 4FH 1BH 6cH n 1BH 51H n 09H 1BH 44H n1 n2 1BH 31H 1BH 41H n 1BH 32H 1BH 4AH n 1BH 4BH n1 00H 1BH 4CH n1 n2 1BH 68H n 1BH 25H n Page 75 13. 2. 1 Command List 13. mma 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 75 76 76 76 77 77 77 78 78 79 79 79 80 80 80 81 81 82 82 83 83 83 84 85 86 86 87 88 89 90 91 Specifying the 8-dot standard density bit image Specifying the 8-dot double density bit image Specifying/Canceling the double height character 41 ESC % n Defining the download character Specifying/Canceling the character set download 1BH 26H 00H n1 n2 74 CITIZEN iDP-3420/3421/3423 User's Manual 42 43 44 45 46 47 48 49 51 52 53 54 55 56 57 58 59 Command ESC BEL n1 n2 BEL FS SUB RS CAN DC3 DC1 ESC @ ENQ STX ETX ESC d 0 ESC d <0> ESC d 1 ESC d <0> ESC t n ESC / n ESC DC3 50 ESC U n Function Setting the external device drive pluse width Driving command A for drawer-1 Driving command B for drawer-1 Driving command for drawer-2 Buzzer-on Canceling the print data Setting the deselect mode Setting the Select mode Unidirectional/bidirectional print mode selection command Initializing the printer Enquiry Text start Text end command Code 1BH 07H n1 n2 07H 1CH 1AH 1EH 18H 13H 11H 1BH 55H n Page 92 92 93 93 93 94 94 94 95 95 96 97 97 99 99 99 100 100 101 101 102 103 60 ESC y n 61 ESC DC2 n1 n2 62 GS * n1 n2 63 GS ¤ m 1BH 40H 05H 02H 03H 1BH 64H 30H Full cut 1BH 64H 00H 1BH 64H 31H Partial cut 1BH 64H 01H Selecting the character code table 1BH 74H n Defining the message 1BH 2FH n Printing the message 1BH 13H n Setting the print lines after paper near end 1BH 79Hn detection Deleting the download character, message 1BH 12H n1 n2 bit image Defining the download, bit image 1DH 2AH n1 n2 Printing the download, bit image 1DH 2FH m 75 CITIZEN iDP-3420/3421/3423 User's Manual Details ils ESC "R" n [Function] [Code] [Range] [Outline] Selecting the international character set <1B>H <52>H n 0 £ n £ 10 This command selects the international characters according to the value of n. Denmark I Sweden n 6 7 8 9 10 Character Set Italy Spain Japan Norway Denmark II Depends upon DIP switch setting. SO [Function] [Code] [Outline] Specifying the double width character <0E>H The data following this command is printed doubled in the horizontal direction. Double width characters remain valid until the double width character cancel command is entered, but they are also cancelled after they are printed one line. Note that the double width characters take up two ordinary characters worth of width. 76 CITIZEN iDP-3420/3421/3423 User's Manual DC4 [Function] [Code] [Outline] Canceling the double width character <14>H This command deselects the double width characters set with SO. The data ESC "E" [Function] [Code] [Outline] Specifying the highlight character <1B>H <45>H The data following this command is printed in highlight (Double) characters. The highlight characters remain valid until the highlight character deselection command is entered. ESC "F" [Function] [Code] [Outline] Canceling the highlight character <1B>H <46>H This command deselects the highlight characters set with ESC "E". The data 77 CITIZEN iDP-3420/3421/3423 User's Manual ESC "-" n [Function] [Code] [Outline] Specifying/Canceling the underline <1B>H <2D>H n This command selects/deselects an underline. 1 £ n1 £ 378/2 This command prints the bit image by the number of data specified with n1. The surplus data exceeding the printable quantity in one line will be ignored. The printer will automatically return to the character mode after printing the bit image. 88 CITIZEN iDP-3420/3421/3423 User's Manual ESC "L" n1 n2 m1 m2 . . . [Function] [Code] [Range] [Outline] Specifying the 8-dot double density bit image <1B>H <4C>H n1 n2 m1 m2 . . . 1 £ n1 + 256 ´ 2 £ 378 This command prints the 8-dot double density (Half-dot print) bit image. The surplus data exceeding the printable quantity in one line will be ignored. The printer will automatically return to the character mode after printing the bit image. The relations between the printing head pin numbers and the data are the same as the 8-dot standard density bit image command. When printing the double density bit image, the horizontally adjacent dots cannot be printed. 89 CITIZEN iDP-3420/3421/3423 User's Manual ESC "h" n [Function] [Code] [Outline] Specifying/Canceling the double height character <1B>H <68>H n The data following this command is printed in double height characters, except the bit image mode <ESC> "K" and <ESC> "L". In combination with the <SO> The double command, this command can print double height, double width characters. It cannot be combined with the inverted character command, <SI>. n 0 30 1 31 Double height character command Deselects Selects 90 CITIZEN iDP-3420/3421/3423 User's Manual ESC "&" <O> n1 n2 m0 m1 m2 m3 m4 m5 m6 m7 m8 m9] n2 - n1 + 1 [Function] [Code] [Range] [Outline] Defining the download character set <1B>H <26>H <00>H n1 n2 [m0 m1 . . . [. . . ] Netzanzeigelämpchen (POWER) (grün) Dieses Lämpchen leuchtet bei eingeschalteter Netzversorgung. Fehlerlämpchen (ERROR) (rot) Dieses Lämpchen leuchtet oder blinkt zur Anzeige eines Fehlers. Fehleranzeige Mechanischer Fehler Papierende Papierrolle fast leer Signalgeber Etwa 1 Sekunde anhaltender Signalton Leuchtet Drei kurze Signaltöne, in Abstand von 0, 6 Sekunden wiederholt werden Blinkt (in Drei kurze Signaltöne, Sekundenabständen) in Abstand von 0, 6 Sekunden wiederholt werden Rasches Blinken Etwa 1 Sekunde langer (zweimal pro Sekunde) Signalton ERROR-Lämpchen Rasches Blinken Rückstellmethode Den Netzschalter rückstellen. Den Papierstau beseitigen. Motorsperre des Schneidemechanism us (nur iDP-3421/23) Mechanischer Fehler : Wenn der Druckmechanismus aufgrund eines Papierstaus o. dergl. höher als normal belastet wird, erklint ein Signalton, und das ERROR-Lämpchen blinkt, um den Druckmechanismus zu stoppen. [. . . ]