User manual CITIZEN MT-801III

[. . . ] ·Slots and openings on the back or bottom of the case are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. The openings should never be blocked by placing the product on a bed, sofa, rug of other similar surface. This product should never be placed near or over a radiator or heater. [. . . ] Character Code Table CBM International CBM Domestic Code Page 850 (Multilingual) Code Page 860 (Portugal) Code Page 863 (Canada-French) Code Page 865 (Norway) n 6 7 8 9 Character Code Table Code Page 852 (Eastern Europe) Code Page 866 (Russia) Code Page 857 (Turkey) Windows Code 255 Space Page (For user setting) - 48 - ESC BEL n1 n2 [Function] [Code] [Range] [Outline] Setting the external device drive pulse width <1B>H <07>H n1 n2 1 £ n1 £ 127 1 £ n2 £ 127 This command sets the power-on time to drive an external device (such as cash drawer). Power-on time = n1 ´ 10 (ms) Delay time = n2 ´ 10 (ms) To actually drive the drawer, use the BEL and FS commands. [Default] n1 = n2 = 20 BEL [Function] [Code] [Outline] Driving command A for drawer-1 <07>H This command drives the drawer connector No. This command is executed in order of entry into - 49 - FS [Function] [Code] [Outline] Driving command B for drawer-1 <1C>H This command drives the drawer connector No. 2 pin under the condition set with the ESC BEL n1 n2 command. SUB [Function] [Code] [Outline] Driving command for drawer-2 <1A>H As soon as this command is received, the drawer connector No. The drawers 1 RS [Function] [Code] [Outline] Buzzer-on <1E>H This command emits a short warning sound from the printer. - 50 - ESC "P" 0 [Function] [Code] [Outline] Full cut <1B>H<50>H<00>H This command fully cuts the paper. (iDP-3551) ESC "P" 1 [Function] [Code] [Outline] Partial cut <1B>H<50>H<01>H This command partially cuts the paper. (iDP-3551) ESC "R" n [Function] [Code] [Range] [Outline] Selecting the international character set <1B>H <52>H n 0 £ n £ 10 This command selects the international characters according to the value of n. Denmark I Sweden n 6 7 8 9 10 Character Set Italy Spain Japan Norway Denmark II Depends upon DIP switch setting. - 51 - ESC "&" <0> n1 n2 [m0 m1 . . . m5 m6 m7 m8 m9] n2 - n1 + 1 [Function] [Code] [Range] [Outline] Defining the Download character set <1B>H <26>H <00>H n1 n2 [m0 m1 . . . m5 m6 m7 m8 m9] n2 - n1 + 1 32 £ n1 £ n2 £ 255 m0 = 0 or m0 = 128 n1 is a character code to start When defining only one This command defines he download characters. character, set n1 = n2. definition and n2 is to end definition, respectively. You can define the ASCII codes ranging from 32 to 255. Once the download characters are defined, they remain valid until they are redefined or the download deletion command (ESC DC2 n1 n2) is executed. - 52 - ESC "%" n [Function] [Code] [Outline] Specifying/Canceling the download character set <IB>H <25>H n This command selects/deselects the download character set. The download characters cannot be printed by simply defining them with the above-mentioned ESC & 0 command. n 0 30 1 31 Download Character Set Deselects Selects ESC "¤" n "data" CR or LF [Function] [Code] [Range] [Outline] Defining the Message <1B>H <2F>H n "data" CR or LF 1 £ n £ 10 This command can define up to a 50-byte message in one line. This command remains valid Red and black characters until the red print deselection command is entered. ESC "5" [Function] [Code] [Outline] Canceling the red print <1B>H <35>H This command deselects red print. - 62 - SI [Function] [Code] [Outline] Specifying the inverted character <0F>H This command selects and prints the inverted characters. Enter it at the Erect and inverted DC2 [Function] [Code] [Outline] Canceling the Inverted character <12>H This command deselects the inverted characters. Enter this command at the LF [Function] [Code] [Outline] Printing and paper feed <0A>H If the print buffer contains the data, this command will feed the line after printing. If not, the command only feeds the line. - 63 - CR [Function] [Code] [Outline] Printing and paper feed (Same as LF) <0D>H The function is the same "LF. " ON, this command is ignored. However, if the DIP switch segment 1-6 is set to ESC "z" [Function] [Code] [Outline] Setting the standard line feed width <1B>H <7A>H This command sets the line feed width as follows. For character type: For graphic type: 1/6 2/9 inch ESC "a" n [Function] [Code] [Range] [Outline] Setting the n-line paper feed <1B>H <61>H n 1 £ n £ 127 This command feeds the paper by the number of lines specified with n. If the print buffer contains the data, use of this command feeds the paper by n-lines after printing the data. - 64 - FF [Function] [Code] [Outline] Form feed (Changing the page) <0C>H This command searches for the head of the next page after printing the data in the print buffer. ESC "C" n [Function] [Code] [Range] [Outline] [Default] Setting the n-line page length <IB>H <43>H n 1 £ n £ 255 Sets the 1-page length to n-lines. n = 42 ESC "C" <0> n [Function] [Code] [Range] [Outline] Setting the n-inch page length <1B>H <43>H <0> n 1 £ n £ 127 This command sets the length of one page to n-inches. - 65 - VT [Function] [Code] [Outline] Vertical tab <0B> H This command feeds the paper to the next vertical tab position. If the current position is equal to or greater than the maximum set vertical tab position, it will be fed to the head of ESC "B" [n]k NUL [Function] [Code] [Range] Setting the vertical tab position <1B>H <42>H [n]k <00>H 1 £ n £ 255 1 £ k £ 16 [Outline] This command cancels the already set vertical tab positions and sets new vertical tab positions. If the tab setting position <nk> is equal or smaller than the preceding set position <nk-1>, it is assumed that setting of the vertical - 66 - ESC "N" n [Function] [Code] [Range] [Outline] [Default] Setting the lower margin <1B>H <4E>H n 0 £ n £ 255 This command sets the n-line lower margin. n=0 ESC "O" [Function] [Code] [Outline] Canceling the lower margin <1B>H <4F>H This command deselects the set lower margin. ESC "l" n [Function] [Code] [Range] [Outline] Setting the left margin <1B>H <6C>H n 0 £ n £ (Right margin - 2) This command sets the left margin and printing starts from the column next to the set margin. - 67 - ESC "Q" n [Function] [Code] [Range] [Outline] Setting the right margin <1B>H <51>H n 2 £ n £ (Max. [. . . ] (Siehe die Beschreibung des Befehls zum Einstellen der Druckzeilenanzahl nach der Erkennung des zuende gehenden Papiervorrats. ) (nur iDP-3551) Schneidemechanismus-Motorsperre : Wenn der Schneidepositionssensor in der Papierschneideeinheit bei laufendem Schneidemotor länger als 1 Sekunde einoder ausgeschaltet ist, wird die Schneide- und Druckfunktion durch Sperren des Motors ausgeschaltet. ­ 141 ­ Pufferdaten löschen : Ist der Drucker eingeschaltet, werden entsprechend der Funktion des Schalters SEL, die Pufferdaten im Eingangsspeicher gelöscht, wie Sie das im Flußdiagramm auf der nächsten Seite sehen. Um die Pufferdaten im Eingangsspeicher zu löschen, schalten Sie den Drucker ein, während Sie gleichzeitig den Schalter SEL drücken. "Clear Data in Buffer" "Cleared Data in Buffer" Um die Pufferdaten im Eingangsspeicher zu drucken, schalten Sie einfach den Drucker ein. Es wird die folgende Meldung gedruckt und die Daten des Eingangsspeichers werden gedruckt. [. . . ]