User manual CITIZEN LC310II

[. . . ] * Slots and openings on the cabinet and the back or bottom are provided for ventilation. To ensure reliable operation of the product and to protect it form overheating, do not block or cover these openings. The openings should never be blocked by placing the product on a bed, sofa, rug of other similar surface. This product should never be placed near or over a radiator or heat register. [. . . ] The compact and light weight printer is sufficiently provided with various functions in order to suffice the requirements of personal computers. This printer is useful especially for receipts and data recording on normal and carboned roll papers. Use this printer properly after reading carefully the manuals of the printer and your computer. 1. 1 Features The printer features the following: 1. Prints in two colors of red and black 1. 2 Accessories Check all your accessories with the following list. O Roll Paper O User's manual O Ink ribbon cassette One set each CITIZEN 6 iDP-562 User's Manual 2. Basic Specifications 1 2 3 4 5 6 7 8 9 10 11 Printing Method Printing Speed Character Column Capacity Character Size Line Spacing Line Feed Speed Character Code Paper Ink Ribbon Cassette Voltage 12 Power 13 Weight 14 Dimensions 15 Interface 16 Operating Temperature 17 Storage Temperature :Serial Dot Matrix :74 LPM with 40column, 235 LPM with 5 column (approx. . ) :7 ´ 5 (Dots) :40 column :2. 75 mm (H) ´ 1. 25 mm (W) :5. 5 mm :6. 2 lines / second approx. . :Refer to character code table :Width 69 ± 1 mm, External diameter 80 mm or less :In red and black; Width 13 mm :120V ± 10% 50 / 60 Hz (for UL, CSA) 230V ± 10% 50 / 60 Hz (for EP) :35 W max. :240 mm (W) ´ 231. 5 mm (D) ´ 111. 5 mm (H) 9. 4" (W) ´ 9. 1" (D) ´ 4. 4" (H) :Serial Interface (RS-232C, TTL Level, Current Loop) NOTE: Current Loop and TTL are a "factory option". 8 bit parallel Interface :5°C ~ 35°C (41°F ~ 95°F) :-25°C~ 60°C (-13°F ~ 140°F) The interface specifications of the iDP562-RSL and iDP562-RSL2 are the same. 3 & 4) Turn the cassette ribbon knob in the direction of the arrow to take up slack in the ribbon. (Fig. 4) CITIZEN 10 iDP-562 User's Manual 4. 2 Loading the Paper (Fig. 5) Paper Insertion procedures 1. (b) TTL Input (RD) Printer side Computer side Equivalent to 7407 Output (DTR FAULT) Note: Output is open collector. CITIZEN 16 iDP-562 User's Manual 5. 5. 2. Setting of Preset jumper Following function are available by setting preset jumper 1 ~ 6. iDP562-RSL2 iDP562-RSL/RS CITIZEN 17 iDP-562 User's Manual Preset jumper Preset Jumper 1 2 3 4 5 Mode CURRENT LOOP TTL × B × B B B B A × B ´ : Both A and B can be set. RS-232C A A A × A B position A position A B DATA can be transferred at DTR = SPACE A (RS-232C / TTL level) DATA can be transferred at DTR = MARK (CURRENT LOOP) DATA can be transferred at DTR = MARK B (RS-232C / TTL level) DATA can be transferred at DTR = SPACE (CURRENT LOOP) At shipping all of preset jumper are set as A. 6 CITIZEN 18 iDP-562 User's Manual 5. 6 DATA Construction 5. 6. 1 Serial Data format 1. Stop BIT (1 ~ 2 BIT) (1) START BIT At 1 / 2 BIT after (a), signal level is checked out, (b). When signal level is MARK, continuous search for START BIT is made for the next bit. (2) DATA BIT + PARITY BIT DATA BIT and PARITY BIT are checked out every 1 / 2 BIT from the half point of START BIT, (b). Signal level of these points (MARK = 1, SPACE = 0) are read as input DATA. The sequence of these BIT is BIT 0, BIT 1 ~ PARITY BIT from START BIT. If SPACE LEVEL is read at STOP BIT, FRAMING ERROR occurs. CITIZEN 19 iDP-562 User's Manual 5. 6. 2. Detection System for Error The printer detects PARITY and FRAMING ERROR. When any error is detected, the printer deletes the wrong DATA and waits for new DATA, ALM LAMP can be put out by depressing SEL switch. [. . . ] *ESC + "K" 1B, 4B It is not possible to print graphic mode and another character mode in one line. ESC + "0" 1B, 4F Paging is off *ESC + "1" 1B, 31 2. 75mm line spacing. DC4 CITIZEN 27 iDP-562 User's Manual 7. 3 Input Data Format The input data to the printer is made by the codes listed in the Character Code Table. 1 Standard Character print Mode Designation US(1F) DATA Designation of standard character print mode is made immediately after power-on and initialization or after print. [. . . ]