User manual CITIZEN LC110II

[. . . ] 8 Registering the bit map data/ESC~b . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Printing the bit map data /ESC~b. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Specifing the font size /ESC~f . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Setting in PAGE MODE/ESC~L. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] m=0 : 8 bit data length 1 : 7 bit data length Sets the serial stop bit length. : n=2 Sets the serial stop bit length. m=0 : 1 stop bit m=1 : 2 stop bit Sets the serial parity bit. : n=3 Sets the parity bit in cable interface connection. m=0 : parity bit unavailable 1: Even Parity 2 Odd Parity Serial interface flow control: n=4 Sets the flow control in cable interface connection. m=0 : XON/XOFF control m=1 : DTR/DSR control Sets the printing density: n=5 Sets the default value of printing density. m=0: Density 0 m=1: Density -1 m=2: Density -2 m=3: Density +1 m=4: Density +2 Sets the type of printing paper: n=6 Sets the default setting for the type of printing paper. m=0: Specifies normal paper m=1: Specifies 2 pieces of carbon paper Setting the operation for automatic feed: n=7 Sets the enabling/disabling of automatic feed. m=0: disabled m=1: enabled 48 Setting the black mark detection:n=8 Sets the enabling/disabling of Marker detection. If auto feed setting is set to enable at the same time, mark detection will be executed during auto feeding as well. m=0: disabled m=1: enabled Setting the character set. : n=9 Sets the default character set. m=1: Graphic character code m=2: Italic code Setting the international characters: n=10 Sets the default setting of international character m=0: Japan 1: USA 2: France 3: Germany 4: England 5: Denmark 6: Sweden 7: Italy 8: Spain 9: Norway 10: Denmark2 11: Spain2 12: LatinAmerica 13: Korea 14: Legal Setting the character pitch: n=12 Sets the default setting of character pitch. m= 0: 10 cpi or equivalent 1: 12 CPI equivalent 2: 15 CPI equivalent 3: Proportional 4: 17 CPI equivalent 5: 20 CPI equivalent Setting the auto power OFF time. : n=13 Sets the auto power OFF time. 3) When horizontal tab (HT) and alignment command (ESC a) are specified at the same time, the horizontal tab (HT) is not available. 4) When absolute position specification command (ESC $) and alignment command (ESC a) are specified at the same time, the absolute position specification command (ESC $) is not available. m=0: Normal 1: Fast Setting the printing of printer's internal setting: n=255 Prints out the current state of internal setting values of the printer. m=0: Prints the printer's internal setting Be sure to write the setting value in the flash memory with ESC~SS after setting categories using this command. The set values become effective at the next power-ON. 52 ESC/P Emulation Command 53 Returning to printing/ CR [ASCII] [Decimal] [Hexadecimal] CR 13 OD [Description] Data in the receiving buffer will not be printed. Moves the print start position immediately after this code to the head of the same line (left margin). * Caution With the use of CR, print data in the same line can be overlapped. Since printing is executed by LF code in PD Series, CR operation includes decoding print data before CR in the printer memory and moving the next print start position (memory decoding position) to the head of the line. 54 Line feed/LF [ASCII] [Decimal] [Hexadecimal] LF 10 0A [Description] Prints the data in the receiving buffer and performs line feed. After setting the LF code, the head of line (left margin) becomes the next printing start position. When print data, CR code, and LF code are entered in this order, data are printed by CR code and then line feed is executed by LF code. Cancels the double-width expansion with automatic cancel (SO, ESC SO). * CautionWhen data without [CR], such as [print data] + [LF], are received, an operation equivalent to CR is executed within LF processing before line feed is executed. [. . . ] 70 ESC K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 ESC I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 ESC L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 ESC M. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]