User manual CITIZEN LC110

[. . . ] ·Do not place this product on an unstable cart, stand or table. ·Slots and openings on the back or bottom of the case are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. The openings should never be blocked by placing the product on a bed, sofa, rug of other similar surface. [. . . ] ·Printer mechanism error ----If the printer mechanism is abnormally loaded due to a paper jam, etc. , the ERROR LED is illuminated, to stop the printer. (3) FEED switch The paper is fed by one line by pressing this switch for a short time, and it is fed continuously by holding down the switch. (4) FEED switch and Power switch Self-print is performed by turning on the Power switch while pressing the FEED switch. 26 CITIZEN iDP-460 User's Manual 4. 9 Print Duty As the printing head mounted onto this printer is not equipped with a head temperature detection sensor (thermistor), the printer protects the printing head against temperature through software. The printer calculates the number of print dots and prints as follows, depending on whether the number of printing dots per line is over or within 500. 1) Within 500 dots Bi-directional prints 2) Over 500 dots Uni-directional prints 27 CITIZEN iDP-460 User's Manual 5. DIP SWITCH SETTING 5. 1 Location of DIP Switch (1) Turn off the power. (Only DS1 provided for the parallel interface) 28 CITIZEN iDP-460 User's Manual <DIP Switches Setting> 1) DS1 Function 1 2 3 4 2) DS2 Function 1 2 3 4 5 6 7 8 Bit length Parity Parity At error Baud rate Baud rate Baud rate Unused See the table below ON 7 bits Yes Even Prints "?" OFF 8 bits No Odd Ignores the data Setting upon Shipment ON ON ON ON OFF ON ON OFF Font Auto loading Not available (*1) Paper used ON Japan Disable -1P OFF International Enable -2P Setting upon Shipment OFF OFF OFF ON The DS2 is used only for the serial interface. 5 OFF ON OFF ON OFF ON OFF ON (*1) 6 OFF OFF ON ON OFF OFF ON ON 7 OFF OFF OFF OFF ON ON ON ON Baud Rate (bps) 150 300 600 1200 2400 4800 9600 19200 Setting of the paper used simply changes the drive pulse width to the printing head; it does not mean that 2-page paper is not available for the 1P setting. The same applies to when 1-page paper is used for the 2P setting. 29 CITIZEN iDP-460 User's Manual 6. PARALLEL INTERFACE 6. 1 Specifications ·Data input system ·Control signals : 8-bit parallel system (DATA1 to DATA8) : ACK, BUSY, STB, FAULT Cable side --- 57-30360 (Ditto) ·Applicable connectors : Printer side --- 57LE-40360 (Equivalent to anphenol), 6. 2 Connector's Pin Confuguration No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Signal Name STB DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 DATA 8 ACK BUSY GND HI-LEVEL GND GND GND FRAME GND No. A sequence of the bits are named Bit 0, Bit 1, . . . , parity bit, starting from the one closest to the start bit. If a space is detected in detecting the stop bit, a framing error results. 37 CITIZEN iDP-460 User's Manual 7. 3. 3 Error Detection A parity error, framing error, and overrun error are detected. When an error is detected, that data is either stored in the buffer as "?" or discarded. (Depends on DIP switch selection) The ERROR lamp is illuminated. (1) Framing error This error results when a space is detected in detecting the stop bit. That data is either stored in the buffer as "?" or discarded. (Depends on DIP switch selection) (2) Parity error If a parity check has been specified and an error is detected at the time of parity check, that data is either stored in the buffer as "?" or discarded. (Depends on DIP switch selection) (3) Overrun error If an overrun error is detected, that data is either stored in the buffer as "?" or discarded. (Depends on DIP switch selection) 7. 3. 4 Data Receiving Control When the DTR signal is a space, the data from the host side can be received. When it is a 7. 3. 5 Buffering The DTR signal is available as a control signal for data transfer to the input buffer. ·Normal print setting Capable of buffering 250-byte data. 38 CITIZEN iDP-460 User's Manual 7. 3. 6 Electrical Characteristics Input (RD, DSR) [Printer Side] [Host Side] (1) RS-232C circuit RD Mark=(-8V): Stop bit Space=(+8V): Start bit Equivalent MAX232 Output (DTR, TD) Equivalent to MAX232 DTR Mark=(-8V): At Busy Space=(+8V): At Ready TD Mark=(-8V): 1 Space=(+8V): 0 39 CITIZEN iDP-460 User's Manual 8. DRAWER KICK-OUT CONNECTOR AND POWER CONNECTOR 8. 1 Specifications of Drawer Kick-Out Connector (D-type Only) (1) Drawer kick-out drive signal The pulses specified by the BELL command(07h) are output. (Approx. [. . . ] Das Farbband durch Drehen des Farbband-Kassettenknopfes in Pfeilrichtung straff wickeln. Zum Herausnehmen der Farbbandkassette die Halteklauen an beiden Seiten zur Seite kippen und die Kassette anheben. 70 CITIZEN iDP-460 User's Manual 4. 5 Einlegen der Papierrolle 1. Mit den Fingern in die Aussparungen an beiden Seiten der Druckerabdeckung greifen, und die Abdeckung durch Anheben bis zum Anschlag öffnen. Das Ende des Druckpapiers in nahezu rechtem Winkel abschneiden. VORSICHT: · Ausschließlich das vorgeschriebene Druckpapier verwenden. · Die Verwendung anderer Papiersorten kann zur Minderung der Druckqualität und zu reduzierter Betriebslebensdauer des Druckers führen. [. . . ]