User manual CITIZEN IDP-562

[. . . ] DOT MATRIX PRINTER MODEL iDP-562 iDP-562 User's Manual Declaration of Conformity Manufacturer's Name : Manufacturer's Address : Japan CBM Corporation : CBM Bldg. , 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Declare the Product Product Name Model Number (s) Dot Matrix Printer iDP-562 Series (iDP-562RSL2, iDP-562RSL, iDP-562CNL, iDP-562RS, iDP-562CN) (S. NO. 60100000 - ) Conform to the following Standards LVD EMC : EN60950 : EN55022 : EN61000-3-2 : EN61000-3-3 : EN50082-1 : IEC801-2 : IEC801-3 : IEC801-4 :1992+A1+A2:1993 :1994 Class B :1995 :1995 :1992 :1991 4KV CD, 8KV AD :1984 3V/m, 27MHz-500MHz :1988 0. 5KV Signal Line 1KV AC mains Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68EEC" Place: Date: Tokyo, Japan January, 1996 Signature: Full Name : Mikio Moriya Position : General Manager R & D Department Europe Contact : Norco Declaration AB Box 7146 S-250 07 Helsingborg Sweden This declaration is applied only for 230V model. CITIZEN iDP-562 User's Manual IMPORTANT SAFETY INSTRUCTIONS * Read all of these instructions and save them for later reference. Slots and openings on the cabinet and the back or bottom are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. [. . . ] Any printing without paper and ink ribbon cassette may cause damage of printer head. Be careful not to drop any foreign matters, such as paper clips, pins and the like into your printer. No organic solvent (alcohol, thinner, benzine or the like) should be used in sweeping clean the surface of the main body case. Make sure that the power of the printer is turned off whenever you do the followings. (1) Taking out any foreign matters which were dropped into the printer. (2) Replacing the ink ribbon cassette. CITIZEN 7 iDP-562 User's Manual 5. Serial Interface 5. 1 Serial Specifications (1) Synchronous Asynchronous (2) Baud rate 150, 300, 600, 1200, 2400, 4800, 9600 BPS One of the above baud rates is selected by users. (3) Data Format Start bit: 1 BIT Data bit: 7 or 8 BIT Parity bit: Odd number parity, even number parity or no parity check, one of which is selected by users. Stop bit: 1 or 2 BIT (4) Signal level RS-232C MARK = 1 (-3V ~ -12V) SPACE = 0 (+3V ~ +12V) CURRENT LOOP MARK = 1 (Current) SPACE = 0 (Non-current) TTL MARK = 1 (Open collector) SPACE = 0 (Open collector) (5) DTR signal RS232C and TTL MARK: Not ready for DATA receipt SPACE: Ready for DATA receipt Current loop When current between connector 17 pin and 24 pin is MARK (Current): Ready for DATA receipt SPACE (Non-current): Not ready for DATA receipt CITIZEN 8 iDP-562 User's Manual 5. 2 Setting of DIP Switch and SLIDE Switch Following function are available by setting DIP switch and SLIDE Switch. DSW-1 DSW-2 DSW-3 CR and LF code When CR code comes are valid function. *OFF CR code is void *OFF CR code is valid ON CR code is valid ON CR code is void CR code is ignored When LF code comes immediately after full buffer When the buffer is blank. *OFF LF code is void ON LF code is valid *OFF LF code is valid ON LF code is void It is recommended to set the DIP switches in accordance with your host's output DATA format. DATA Form DATA + CR DATA + LF DATA + CR + LF DATA + LF + CR Foreign character Selection DSW-1 DSW-2 DSW-3 OFF OFF OFF ON OFF OFF DSW-4 DSW-5 DSW-6 DSW-7 DSW-8 SSW *OFF -1 ON DSW-9 DSW-10 Parity check Selection of DATA bit length Selection of Baud Rate USA *OFF *OFF ODD *OFF OFF ON *OFF 9600 1200 *OFF *OFF GERMANY OFF ON EVEN ON OFF 4800 600 OFF ON FRANCE UK ON ON OFF ON No Check *OFF ON *ON *ON 7 bit DATA 8 bit DATA 2400 1200 300 150 ON ON OFF ON NOTE: * Marks are a "Factory Setting". CITIZEN 9 iDP-562 User's Manual 5. 3 Connectors and Signals Signal Pin 1 7 3 20 14 25 17 23 24 Return Line Signal Name FG SG RD DTR FAULT RD DTR Direction of Signal Function Frame GND GND Input DATA BUSY signal ALARM signal Input DATA BUSY signal A: Computer B: Printer RS232C CURRENT LOOP TTL AB Notes: 1. Selection of modes, those are RS-232C, CURRENT LOOP and TTL, can be made by the preset jumper (Please refer to `Setting of Preset Jumper'). Compatible Connector (D-Subconnector): * Printer: 17LE-13250 (AMPHENOL or equivalent) * Cable Side: 17JE-23250 (AMPHENOL or equivalent) 5. 4 Interface Circuit RS-232C Input (RD) Printer side Computer side Equivalent to 232 Output (DTR FAULT) Equivalent to 232 CITIZEN 10 iDP-562 User's Manual 5. 5 Current Loop and TTL 5. 5. 1 Interface Circuit (a) Current Loop Input (RD) Printer side Computer side Output (DTR) Note: Resistance should be set so that Current Loop is restricted within 10 ~ 20 mA. (b) TTL Input (RD) Printer side Computer side Equivalent to 7407 Output (DTR FAULT) Note: Output is open collector. CITIZEN 11 iDP-562 User's Manual 5. 5. 2. Setting of Preset jumper Following function are available by setting preset jumper 1 ~ 6. iDP-562-RSL2 iDP-562-RSL/RS CITIZEN 12 iDP-562 User's Manual Preset jumper Preset Jumper 1 2 3 4 5 Mode CURRENT LOOP TTL × B × B B B B A × B × : Both A and B can be set. RS-232C A A A × A B position A position A B DATA can be transferred at DTR = SPACE (RS-232C / TTL level) DATA can be transferred at DTR = MARK (CURRENT LOOP) DATA can be transferred at DTR = MARK B (RS-232C / TTL level) DATA can be transferred at DTR = SPACE (CURRENT LOOP) At shipping all of preset jumper are set as A. A 6 CITIZEN 13 iDP-562 User's Manual 5. 6 DATA Construction 5. 6. 1 Serial Data format 1. Stop BIT (1 ~ 2 BIT) (1) START BIT At 1 / 2 BIT after (a), signal level is checked out, (b). When signal level is MARK, continuous search for START BIT is made for the next bit. DATA BIT + PARITY BIT DATA BIT and PARITY BIT are checked out every 1 / 2 BIT from the half point of START BIT, (b). [. . . ] In addition, when the data of 40 characters (standard character mode) is input in one line, an automatic line feed is carried out after printing (full buffer print). 2 Enhanced Character Print Mode Designation RS(1E) DATA CR(0D) All the print data which follow RS code are enhanced and are reversed to standard character by US code. Automatic printing is carried out when full column data (40 columns in standard character) is input. 3 Red Print Mode Designation DC(12) DATA CR(0D) Red Print Mode is designated by DC2 code and released after printing one line. [. . . ]