User manual CITIZEN IDP-3530

[. . . ] CITIZEN User's Manual MINI DOT MATRIX PRINTER MODEL iDP-3530 Japan CBM Corporation Information Systems Div. iDP-3530 User's Manual IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference. For Uses in Canada This digital apparatus does not exceed the class A limits for radio noise emissions from digital, apparatus, as set out in the radio interface regulations of the Canadian department of communications. CITIZEN 2 iDP-3530 User's Manual CONTENTS 1. [. . . ] Any printing without paper and ribbon cassette may cause damage to printer head. 3) Be careful not to drop any foreign objects, such as paper clips, pins and the like into your printer. 5) Always place your printer on a stable desk which is set horizontal. 6) No organic solvent (thinner, benzene or the like) shall be used in sweeping clean the surface of the main body case. 7) Make sure that the power of the printer is turned off whenever you do the following. (1) Taking out any foreign matter which were dropped into the printer. (2) Replacing the ribbon cassette. CITIZEN 13 iDP-3530 User's Manual 5. Serial Interface 5-1 Specifications 1) Synchronism : Asynchronous 2) Baud rate : 1200, 2400, 4800, 9600 BPS (Selected by user) 3) Composition of one word : Start bit : 1 bit Data bit : 7 or 8 bit (selected by user) Parity bit : Odd, even or parity (selected by user) Stop bit : 1 bit or more. 4) Signal polarity : RS-232C : Mark = Logic "1" (-3V to -12V) : Space = Logic "0" (+3V to +12V) 4) Receiving Control (DTR signal) : RS-232C : Mark = Data transfer not possible : Space = Data transfer possible 5-2 Connector Pin Assignment Pin No. 1 3 7 14 20 Signal Name FG RD SG FAULT DTR Direction Host / Printer Function Safety Ground Received Data Signal Ground Printer ALARM Signal Printer BUSY Signal RS-232C ¡ ¡ ¡ Notes: 1. Please always maintain the "Mark state", when received data is not being transferred. Compatible connector (D-Sub connector) Printer side: Equivalent to AMPHENOL 17-13250 Cable side: Equivalent to AMPHENOL 17-23250 CITIZEN 14 iDP-3530 User's Manual 5-3 Input / output Signals RS-232C Circuit Input (RD) [Printer side] [Host side] uPD4711 or equivalent Output (DTR, FAULT) [Printer side] [Host side] uPD4711 or equivalent DTR : (-8V) BUSY : (+8V) READY FAULT : (-8V) Normal : (+8V) Abnormal CITIZEN 15 iDP-3530 User's Manual 5-4 Data Composition [1] Start bit [2] Data bits (and parity bit) [3] Stop bit (1 bit more) 1) Start bit 1/2 bit past the line dropping from MARK to SPACE, a status reading is taken again. If the reading is SPACE, a start bit is recognized. 2) Data bits and Parity bit Data bit and Parity bit are checked out every bit form the half point of start bit. Signal level of these points (Mark = 1, Space = 0) are read as input data. The sequence of these bit is Bit 0, Bit 1 ~ Parity bit from Start bit. 3) Stop bit The stop bit consists of one or more bits at "mark" level. When "space" level is detected for a stop bit, a framing error occurs. 5-5 Error Detection The printer detects Parity, Framing and Overrun Error. Framing Error; Framing error occurs when SPACE signal is checked out at STOP BIT and the printer print out (7FH). Parity Error; Parity check is carried out only when user designates it on the printer pre-setting. Input Control and Buffering; (over-run-error) The printer is designed to output DTR signals for each word. [. . . ] The same function as US code is performed by using SI code (except for serial 7 bit data use). (2) Double-Width Character Print Mode Designation RS (1E) DATA CR (0D) All print data following RS code are printed out in double-width size and this code can be released by US code. It is possible to mix the characters in normal width and double width on one line. However, because a double-width character requires twice the normal width, take care not to exceed the column capacity of the printer. [. . . ]