User manual CITIZEN IDP-3420

[. . . ] DOT MATRIX PRINTER MODEL iDP3420 iDP3421 iDP3423 User's Manual iDP3420/3421/3423 User's Manual Declaration of Conformity This printer conforms to the following Standards: Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC. LVD : EN60950 EMC : EN55022 Class A EN61000-3-2 EN61000-3-3 EN55024 This declaration is applied only for 230V model. CITIZEN is a registered trade mark of CITIZEN WATCH CO. , LTD. , Japan CITIZEN es una marca registrada de CITIZEN WATCH CO. , LTD. , Japón ESC/POS and EPSON are a trademark and registered trademark of SEIKO EPSON CORPORATION Star is a registered trademark of Star Micronics Corporation Windows is a registered trademark of Microsoft Corporation CITIZEN iDP3420/3421/3423 User's Manual IMPORTANT SAFETY INSTRUCTIONS · · · · · · Read all of these instructions and save them for future reference. Slots and openings on the back or bottom of the case are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. The openings should never be blocked by placing the product on a bed, sofa, rug of other similar surface. [. . . ] Denmark I Sweden n 6 7 8 9 10 Character Set Italy Spain Japan Norway Denmark II [Range] [Outline] [Default] Depends upon DIP switch setting. 52 CITIZEN iDP3420/3421/3423 User's Manual ESC "&" <0> n1 n2 [m0 m1 . . . m5 m6 m7 m8 m9] n2 - n1 + 1 [Function] Defining the Download character set [Code] <1B>H <26>H <00>H n1 n2 [m0 m1 . . . m5 m6 m7 m8 m9] n2 - n1 + 1 32 n1 n2 255 [Range] [Outline] m0 = 0 or m0 = 128 n1 is a character code to start definition This command defines he download characters. and n2 is to end definition, respectively. When defining only one character, set n1 = n2. Once the download characters are You can define the ASCII codes ranging from 32 to 255. defined, they remain valid until they are redefined or the download deletion command (ESC DC2 n1 n2) is executed. 53 CITIZEN iDP3420/3421/3423 User's Manual ESC "%" n [Function] Specifying/Canceling the download character set [Code] <IB>H <25>H n [Outline] This command selects/deselects the download character set. The download characters cannot be printed by simply defining them with the above-mentioned ESC & 0 command. n 0 30 1 31 Download Character Set Deselects Selects ESC "/" n "data" CR or LF [Function] Defining the Message [Code] <1B>H <2F>H n "data" CR or LF 1 n 10 This command can define up to a 50-byte message in one line. If the value of n is specified [Range] [Outline] beyond the range, the data following n will be treated as the print data. Once the message is defined, it remains valid until it is redefined or the download deletion command (ESC DC2 n1 n2) is executed. The data should end with If the data exceeds 50 bytes, the subsequent data will be treated as 54 CITIZEN iDP3420/3421/3423 User's Manual ESC DC3 n [Function] Printing the message [Code] <1B>H <13>H n 1 n 10 This command prints a message. If the value of n is specified beyond the range, the [Range] [Function] ESC "y" n [Function] Setting the print lines after paper near end detection [Code] <1B>H<79>H n 0 n1 255 This command sets the number of print lines after paper near end detection. It stops [Range] [Outline] printing after printing n × 2 lines since detection of the paper near end, resulting in the paper near end state (See 4. 12 Operation Panel and Error Indications). The PE signal [Default] n=0 55 CITIZEN iDP3420/3421/3423 User's Manual ESC DC2 n1 n2 [Function] Deleting the download character, message, bit image [Code] <1B>H <12>H n1 n2 0 n1 3 0 n2 (Specify 0 at n1 = 0) (1 n2 10 at n1 = 1) (32 n2 255 at n1 = 2) (Specify 0 at n1 = 3) [Range] [Outline] This command deletes the downloaded characters, message, and bit image. n1 0 1 2 3 Object Deleted All(Message, characters, bit image) Download message Download characters Download bit image With n2, specify which data of the function specified with n1 should be deleted. n2 = 0 n20 Deletes all the data saved with the download function specified with n1. Deletes the data downloaded at the value specified with n2 (Value specified when saving with each download command), of the d ownload function specified with n1. Note) No meaning when n1 = 0 is set. 56 CITIZEN iDP3420/3421/3423 User's Manual GS "" n1 n2 [d] n1 × n2 × 8 [Function] Defining the download, bit image <1D>H <2A>H <n1> <n2> [<d>] n1 × n2 × 8 1 n1 45 0 n2 24 [Code] [Range] Note) Take care that the number of data (n1×n2×8) is equal to or smaller than 2, 048. [Outline] This command defines the download bit image having the dots specified n1 and n2. printout. ) The number of horizontal dots is represented by n1 × 8 and that of vertical dots is represented by m denotes the number to be registered. Once the download bit image is defined, it remains valid until it is redefined or the download deletion command (ESC DC2 n1 n2) is executed. 57 CITIZEN iDP3420/3421/3423 User's Manual GS / m [Function] Printing the download, bit image [Code] <1D>H <2F>H m 0 m 255 This command prints the bit image saved in the number specified with m. [Range] [Outline] [Caution] If the print buffer contains the data, this command will be ignored. Nothing is printed when m is other than 0, 1, 2 or 3. If the bit image has not 58 CITIZEN iDP3420/3421/3423 User's Manual 13. 2 13. 2. 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Star Mode Command List Command ESC R n ESC 6 ESC 7 ESC M ESC P ESC : SO DC4 ESC E ESC F ESC - ESC _ ESC 4 ESC 5 SI DC2 LF CR ESC z ESC 0 ESC a n FF ESC C n ESC C 0 n VT ESC B n1 n2 ESC N n ESC 0 ESC 1 n ESC Q [n] k NUL HT ESC D n1 n2 ESC 1 ESC A n ESC 2 ESC J n ESC K n1 <0> ESC L n1 n2 ESC h n ESC & <0> n1 n2 ESC % n Function Selecting the international character set NOP NOP NOP NOP NOP Specifying the double width character Canceling the double width character Specifying the highlight character Canceling the highlight character Specifying/Canceling the underline NOP Specifying the red print Canceling the red print Specifying the inverted character Canceling the inverted character Printing and paper feed Printing Setting the 1/6-inch line feed NOP n-line paper feed Form feed (Change the page) Setting the n-line page length Setting the n-inch page length Vertical tab Setting the vertical tab position Setting the lower margin Canceling the lower margin Setting the left margin Setting the right margin Horizontal tab Setting the horizontal tab position Setting the 1/9-inch line feed width NOP Setting the 2/9-inch line feed width NOP Specifying the 8-dot standard density bit image Specifying the 8-dot double density bit image Specifying/Canceling the double height character Defining the download character Specifying/Canceling the download character set Code 1BH 52H n 1BH 36H 1BH 37H 1BH 4DH 1BH 50H 1BH 3AH 0EH 14H 1BH 45H 1BH 46H 1BH 2DH n 1BH 5FH n 1BH 34H 1BH 35H 0FH 12H 0AH 0DH 1BH 7AH 1BH 30H 1BH 61H n 0CH 1BH 43H n 1BH 43H 00 n 0BH 1BH 42H n1 n2 1BH 4EH n 1BH 4FH 1BH 6cH n 1BH 51H n 09H 1BH 44H n1 n2 1BH 31H 1BH 41H n 1BH 32H 1BH 4AH n 1BH 4BH n1 00H 1BH 4CH n1 n2 1BH 68H n 1BH 26H 00H n1 n2 1BH 25H n Page 61 61 62 62 62 63 63 63 64 64 65 65 65 66 66 66 67 67 68 68 69 69 69 70 71 72 72 73 74 75 76 77 59 CITIZEN iDP3420/3421/3423 User's Manual 42 43 44 45 46 47 48 49 50 Command ESC BEL n1 n2 BEL FS SUB RS CAN DC3 DC1 ESC U n 51 ESC @ 52 ENQ 53 STX 54 ETX ESC d 0 55 ESC d <0> ESC d 1 56 ESC d <0> 57 ESC t n 58 ESC / n 59 ESC DC3 60 ESC y n 61 62 63 ESC DC2 n1 n2 GS n1 n2 GS / m 1BH 40H 05H 02H 03H 1BH 64H 30H Full cut 1BH 64H 00H 1BH 64H 31H Partial cut 1BH 64H 01H Selecting the character code table 1BH 74H n Defining the message 1BH 2FH n Printing the message 1BH 13H n Setting the print lines after paper near end detection 1BH 79Hn Deleting the download character, message bit 1BH 12H n1 n2 image Defining the download, bit image 1DH 2AH n1 n2 Printing the download, bit image 1DH 2FH m Function Setting the external device drive plus e width Driving command A for drawer-1 Driving command B for drawer-1 Driving command for drawer-2 Buzzer-on Canceling the print data Setting the deselect mode Setting the Select mode Unidirectional/bidirectional print mode selection command Initializing the printer Enquiry Text start Text end command Code 1BH 07H n1 n2 07H 1CH 1AH 1EH 18H 13H 11H 1BH 55H n Page 78 78 79 79 79 80 80 80 81 81 82 83 83 85 85 85 86 86 87 87 88 89 60 CITIZEN iDP3420/3421/3423 User's Manual Details ESC "R" n [Function] Selecting the international character set [Code] <1B>H <52>H n 0 n 10 This command selects the international characters according to the value of n. Denmark I Sweden n 6 7 8 9 10 Character Set Italy Spain Japan Norway Denmark II [Range] [Outline] [Default] Depends upon DIP switch setting. SO [Function] Specifying the double width character [Code] <0E>H [Outline] The data following this command is printed doubled in the horizontal direction. Double width characters remain valid until the double width character cancel command is entered, but they are also cancelled after they are printed one line. Note that the double width 61 CITIZEN iDP3420/3421/3423 User's Manual DC4 [Function] Canceling the double width character [Code] <14>H [Outline] This command deselects the double width characters set with SO. [. . . ] Fehleranzeige ERROR-Lämpchen Signalgeber Mechanischer Fehler Rasches Blinken Etwa 1 Sekunde anhaltender Signalton Papierende Leuchtet Drei kurze Signaltöne, in Abstand von 0, 6 Sekunden wiederholt werden Papierrolle fast leer Blinkt (in Drei kurze Signaltöne, in Sekundenabständen) Abstand von 0, 6 Sekunden wiederholt werden Motorsperre des Rasches Blinken Etwa 1 Sekunde langer Schneidemechanismus (zweimal pro Sekunde) Signalton (nur iDP3421/23) Mechanischer Fehler Rückstellmethode Den Netzschalter rückstellen. Den Papierstau beseitigen. : Wenn der Druckmechanismus aufgrund eines Papierstaus o. höher als normal belastet wird, erklint ein Signalton, und das ERROR-Lämpchen blinkt, um den Druckmechanismus zu stoppen. Papierende : Bei aufgebrauchte-m Papiervorrat erkennt der Sensor im Papierweg in der Nähe des Druckkopfes das Ende der Papierrolle, schaltet den Signalgeber und das ERROR-Lämpchen ein, um den Druckmechanismus zu stoppen. Durch Einschieben des Papiers in den Papierweg wird die Papierrolle geladen (siehe 4. 7 "Einlegen des Papiers"). Papiervorrat fast leer : Bei aufgebrauchtem Papiervorrat wird der Papierrestsensor zum Einschalten des Signalgebers und des ERROR-Lämpchens aktiviert. [. . . ]