User manual CITIZEN IDP-3410

[. . . ] DOT MATRIX PRINTER MODEL iDP3410 iDP3410 User's Manual Declaration of Conformity Manufacturer's Name : Manufacturer's Address : Japan CBM Corporation CBM Bldg. , 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Declare the Product Product Name : Model Number (s) : Dot Matrix Printer iDP3410 (iDP3410R/P, iDP3410S/C, iDP3410T/I) (S. NO. 98X0001 - ) Conform to the following Standards LVD : EMC : EN60950 EN55022 EN61000-3-2 EN61000-3-3 EN50082-1 IEC801-2 IEC801-3 IEC801-4 : 1992+A1+A2+A3+A4 : 1994 Class A : 1995 : 1995 : 1992 : 1991 4KV CD, 8KV AD : 1984 3V/m, 26MHz-1000MHz AM1KHz 80% : 1988 0. 5KV Signal Line ± 1KV AC mains Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC" Place : Tokyo, Japan Date : September1995 Signature: Full Name : Mikio Moriya Position : General Manager R & D Department Europe Contact : Norco Declaration AB Box 7146 S-250 07 Helsingborg, Sweden WARNING This is a Class A products. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Dans environement domestique, il peut causer des interférences radio. Auquel cas, l'utilisateur sera amené à prendre les mesures adéquates. [. . . ] Shows a command. [Range] [Outline] [Caution] [Default] XXX 35 CITIZEN iDP3410 User's Manual Details FF n [Function] [Code] [Range] [Outline] n-line paper feed <0C>H n 1 n 127 This command feeds the paper by n-lines. If the print buffer contains the data, use of this command feeds the paper by n-lines after printing the data. Setting n = 0 does not feed the paper. SO [Function] [Code] [Outline] Specifying the double width character <0E>H The data following this command is printed doubled in the horizontal direction. Double width characters remain valid until the double width character cancel command is entered, but they are also cancelled after they are printed one line. Note that the double width characters take up two ordinary characters worth of width. 36 CITIZEN iDP3410 User's Manual SI [Function] [Code] [Outline] Canceling the double width character <0F>H This command cancels the double width characters set with SO. The data following this command are printed in the ordinary character width. LF [Function] [Code] [Outline] Printing and paper feed <0A>H If the print buffer contains the data, this command will feed the line after printing. If not, the command only feeds the line. CR [Function] [Code] [Outline] Printing <0D>H This command prints the data. If the DIP switch segments 1 to 6 are set to OFF, the printer will print the data in the print buffer and feed the paper by one line. If they are set to ON, the printer will print the data in the print buffer and will not feed the paper. DC1 [Function] [Code] [Outline] Initializing the printer <11>H This command initializes the printer. The settings of the DIP switch segments are not re-read. DC2 [Function] [Code] [Outline] Specifying/Canceling the inverted character <12>H This command selects/deselects the inverted characters. Erect and inverted characters cannot be mixed in one line. 37 CITIZEN iDP3410 User's Manual DC3 [Function] [Code] [Outline] Specifying the red print <13>H This command specifies red-color characters. All the characters in one line are printed in red by prefixing the print data with this command and sending it to the printer. When you want to use red characters, use this command for each line. CAN [Function] [Code] [Outline] Canceling the print data <18>H This command clears the print data in the lines entered prior to this command. 38 CITIZEN iDP3410 User's Manual ESC "*" n1 n2 [Function] [Code] [Range] [Outline] Specifying the bit image mode <1B>H <2A>H n1 n2 1 n1 + 256 × n2 378 This command allows printing in the bit image mode. Divide the number of dots printed by 256 and assume its quotient to be n2 and remainder to be n1. If the bit image data is entered beyond the dot positions printable in one line, the surplus data will be discarded. Printing is done in a single direction. ESC "-" n [Function] [Code] [Outline] [Default] Specifying/Canceling the underline <1B>H <2D>H n This command selects/deselects an underline. n=0 ESC "1" [Function] [Code] [Outline] Setting the 1/9-inch line feed width <1B>H <31>H This command sets the line feed width to 1/9 inch. 39 CITIZEN iDP3410 User's Manual ESC "2" [Function] [Code] [Outline] Setting the 2/9-inch line feed width <1B>H <32>H This command sets the line feed width to 2/9 inch. ESC "3" [Function] [Code] [Outline] Setting the 1/6-inch line feed width <1B>H <33>H This command sets the line feed width to 1/6 inch(Default). ESC "C" n [Function] [Code] [Range] [Outline] Setting the page length <1B>H <43>H n 1 n 127 Sets the 1-page length to n-lines. 40 CITIZEN iDP3410 User's Manual ESC "N" n [Function] [Code] [Range] [Outline] Specifying the perforation skip <1B>H <4E>H n 1 n 126 This command feeds(Skips) the lines specified with n without printing. However, you cannot specify beyond the length of one page. ESC "O" [Function] [Code] [Outline] Canceling the perforation skip <1B>H <4F>H This command cancels perforation skipping operation. ESC "f" 1 [Function] [Code] [Outline] Form feed (Changing the page) <1B>H <66>H <01>H This command searches for the beginning of the next page after printing the data in the print buffer. 41 CITIZEN iDP3410 User's Manual ESC "t" n [Function] [Code] [Range] [Outline] [Default] n 0 1 2 3 4 5 Selecting the character code table <1B>H <74>H n 0 n 255 This command selects Page-n of Character Code Table. Character Code Table CBM International CBM Domestic Code Page 850 (Multilingual) Code Page 860 (Portugal) Code Page 863 (Canada-French) Code Page 865 (Norway) n 6 7 8 9 255 Character Code Table Code Page 852 (Eastern Europe) Code Page 866 (Russia) Code Page 857 (Turkey) Windows Code Space Page (For user setting) 42 CITIZEN iDP3410 User's Manual ESC BEL n1 n2 [Function] [Code] [Range] [Outline] Setting the external device drive pulse width <1B>H <07>H n1 n2 1 n1 127 1 n2 127 This command sets the power-on time to drive an external device (Cash drawer). Power-on time = n1 × 10 (ms) Delay time = n2 × 10 (ms) To actually drive the drawer, use the <BEL> and <FS> commands. n1 = n2 = 20 [Default] BEL [Function] [Code] [Outline] Driving command A for drawer-1 <07>H This command drives the drawer connector no. 2 pin under the condition set with the <ESC><BEL> n1 n2 command. [. . . ] Netzanzeigelämpchen (grün) (POWER) Leuchtet bei eingeschalteter Netzversorgung. Fehleranzeigelämpchen (rot) (ERROR) Leuchtet, wenn das Papier aufgebraucht ist oder ein Fehler im Druckmechanismus oder in der Kommunikations auftritt. <Fehleranzeigen> ·Papierende: Wenn sich das Papier dem Ende nähert, erkennt ein Sensor, der sich am Papierweg in der Nähe des Druckkopfes befindet, das Papierende und schaltet das LEDFehleranzeigelämpchen ein. Durch Einschieben des Papiers in den Papierweg wird das Papier eingezogen. [. . . ]