User manual CITIZEN IDP-3310

[. . . ] SERIAL THERMAL PRINTER MODEL iDP3310 iDP3310 User's Manual IMPORTANT SAFETY INSTRUCTIONS · Read all of these instructions and save them for future reference. · Do not place this product on an unstable cart, stand or table. · Slots and openings on the back or bottom of the case are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. [. . . ] (3) Overrun error On detection of an overrun error, the data are canceled. 7. 3. 4 Data Receiving Control If the DTR signal is a "Space", the data can be received from the host side, but if it is a "Mark", the data cannot be received. 7. 3. 5 Buffering The DTR signal is available as a control signal for transferring the data to the input buffer. (See the page 27, 7. 3. 1-(2)) · Normal print mode Capable of buffering the 250-byte data. If the data exceeds 1 k-byte, the preceding 1 kbyte data will be printed repeatedly. 29 CITIZEN iDP3310 User's Manual 7. 3. 6 Electrical Characteristics (1) RS-232C Circuit Input (RD, DSR) [Printer Side] [Host Side] RD Mark=(-8V): Stop bit Space=(+8V): Start bit Equivalent MAX232 Output (DTR, TD) DTR Equivalent MAX232 Mark=(-8V): At Busy Space=(+8V): At Ready TD Mark=(-8V): 1 Space=(+8V): 0 30 CITIZEN iDP3310 User's Manual 8. DRAWER KICK-OUT CONNECTOR AND POWER CONNECTOR 8. 1 Specifications of Drawer Kick-Out Connector(Option) (1) Drawer kick-out drive signal The pulses specified by the BELL command(07h) are output. (Approx. 200 ms) (2) Electrical characteristics 1) Drive voltage: 12V DC +/- 1V 2) Drive current: 0. 8 A at maximum 8. 1. 1 Connector's Pin Configuration No. Signal Function 1 FG Frame Ground 2 DRAWER 1 Drawer drive signal 3 -4 VDR Drawer drive power 5 -6 -Connector used Applicable connector : TM5RJ3-66(HIROSE) or equivalent : TM3P-66P(HIROSE) or equivalent CAUTION : · No output is made while printing. 8. 1. 2 Drive Circuit [Printer Side] 31 CITIZEN iDP3310 User's Manual 8. 2 Power Supply Connector Specifications This is a power connector from an exclusive AC adapter. 1 2 1 Function +17V GND 2 Jack used : HEC0470-01-640(HOSHIDEN) or equivalent Applicable plug : JXP series Type-A (I. D. 5. 5 mm) (HOSHIDEN) or equivalent CAUTION: · Be sure to use the specified power supply. · Do not connect the power supply with different polarities. 32 CITIZEN iDP3310 User's Manual 9. MAINTENANCE AND SERVICE For the information on maintenance and service, please contact our dealer or at the following address. Northern America CBM America Corporation Service Center 365 Van Ness Way Suit 510 Torrance, CA 90501, U. S. A TEL +1-310-781-1460 FAX +1-310-781-9157 Other Areas Japan CBM Corporation Information Systems Division CBM Bldg. , 5-68-10 Nakano Nakno-ku, Tokyo 164-0001 Japan TEL +81-3-5345-7540 FAX +81-3-5345-7541 33 CITIZEN iDP3310 User's Manual 10. PRINT CONTROL FUNCTIONS 10. 1 Commands List Command LF CR FF CAN NULL DC2 DC3 FS GS RS US SO SI BELL ESC a(n); ESC b(n); ESC c ESC d ESC e(n); ESC f(n); ESC g ESC h(n); ESC i ESC x ESC C n ESC O ESC * m nn ESC Y Function Line Feed Print Eject Paper Clear Print Buffer Cancel Character Attribute Pad Character(NOP) Specify Underline Specify the Repeat Print Execute P-250 Mode Execute P-200 Mode Set Double Width Character Set Normal Width Character Set Double Width Character or specify High Page Set Normal Width Character or Reset Character code Drawer Kick-out(D-type only) Set Line Height Eject Paper by n lines Initialize Request Printer Status Set Right Margin Set Line Attribute Graphic Mode Activate Select Character Set Identify Printer Select P-900R Mode Set Page Length and Paging Cancel Paging Specify Bit Image Mode Specify the Repeat Print 0AH 0DH 0CH 18H 00H 12H 13H 1CH 1DH 1EH 1FH 0EH 0FH 07H 1BH61H(n)3BH 1BH62H(n)3BH 1BH63H 1BH64H 1BH65H(n)3BH 1BH66H(n)3BH 1BH67H 1BH68H(n)3BH 1BH69H 1BH78H 1BH43H n 1BH4FH 1BH2AH m n 1BH59H Code P-250 P-200 P-250 iDP-562 40 ch 42 ch Refer to × × 37 37 38 38 39 39 39 40 40 41 41 42 42 43 43 44 44 45 45 46 - 46 47 47 48 48 49 50 × × × × × × × × × × × × × × × × × × × × * P-250 represents both P-250 and P-900R modes. P-250 mode basically equals to P-900R except the printer ID and some status sent to the host from the printer. : Command enable, ×: Command disable * * n m in the code indicates the character codes 00h to FFh. 34 CITIZEN iDP3310 User's Manual 10. 2 Command Sets The command sets are set by the setting of the DIP switches and specific commands. The available commands and functions differ depending on each setting. (1) P-250 command set There are two kinds of modes: P-200 mode and P-250 mode. If the P-250 command set is set with the DIP switches, the P-200 mode will be effected. The P-250 mode or P-900R mode are available with the P-250 mode or P-900R mode command. The SI, SO, RS, US, and DC2 command operate differently between the P-200 mode and P-250 mode. [. . . ] Andernfalls können beim Start des automatischen Papiervorschubs Funktionsstörungen oder ein Papierstau auftreten. · Nech dem automatischen Papiervorschub ist der Drucker betriebsbereit. Bitte beachten: Wenn noch Daten im Puffer vorhanden sind oder empfangen werden, startet der Druckbetrieb nach dem Vorschieben des Papiers automatisch. 70 CITIZEN iDP3310 User's Manual 4. 10 Papierstau und Reißen beim Druckbetrieb In den folgenden Fällen können Funktionsstörungen, wie z. B. In derartigen Fällen sollte der Drucker aus- und wieder eingeschaltet weden. [. . . ]