User manual CITIZEN IDP-3240

[. . . ] LINE THERMAL PRINTER MODEL iDP3240 User's Manual WEEE MARK En Ge Fr Sp It Du Da Por Pol Declaration of Conformity This printer conforms to the following Standards: Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC. LVD : EN60950 EMC : EN55022 EN61000-3-2 EN61000-3-3 EN55024 Class A This declaration is applied only for 230V model. WARNING : This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CITIZEN is registered trade mark of CITIZEN WATCH CO. , LTD. , Japan CITIZEN es una marca registrada de CITIZEN WATCH CO. , LTD. , Japón Windows codepage is a registered trademark of Microsoft Corporation --i-- IMPORTANT SAFETY INSTRUCTIONS · Read all of these instructions and save them for future reference. · Do not place this product on an unstable cart, stand or table. · Slots and openings on the back or bottom of the case are provided for ventilation. [. . . ] · The beginning of the line is specified as the next print start position. [Caution] [Default] [Sample Program] If [n × line feed width] exceeds approximately 1016 mm, this command feeds paper by approximately 1016 mm (40 inches). LPRINT "AAAAA"; LPRINT CHR$(&H1B) + "d" + CHR$(2); LPRINT "AAAAA" + CHR$(&HA); END AAAAA [Print Results] AAAAA 2/6-inch line feed -- 91 -- ESC p m n1 n2 [Function] [Code] [Range] Generating the specified pulses <1B>H<70>H<m><n1><n2> m = 0, 1, 48, 49 0 0 [Outline] n1 n2 255 255 The signals specified by "n1" and "n2" are output to the connector pin specified by "m". · "m" has the followings. m 0, 48 1, 49 Connector Pin Drawer Kick-Out pin No. 2 Drawer Kick-Out pin No. 5 · The ON time is n1 × 2 ms, and OFF time n2 × 2 ms. [Caution] · When "m" is beyond a definition range, no signal is output, discarding "n1" and "n2". · The drawer drive duty must be within the following range: ON time ON time + OFF time (The OFF time should be 4 times or more longer than the ON time. ) [Default] [Sample Program] The initial value for "m", "n1" and "n2" is not defined. LPRINT CHR$(&H1B) + "p"; LPRINT CHR$(0); Selects pin No. LPRINT CHR$(5); Sets ON time to 10ms LPRINT CHR$(50); Sets OFF time to 100ms END 0. 2 -- 92 -- ESC t n [Function] [Code] [Range] [Outline] Selecting the character code table <1B>H<74>H<n> 0 n 9, n = 255 Selecting the character code table: The character code table is selected based on the value of "n". n 0 1 2 3 4 5 6 7 8 9 255 Character Code Table Codepage PC437 (USA, European Standard) Codepage Katakana (Japanese) Codepage PC850 (Multilingual) Codepage PC860 (Portuguese) Codepage PC863 (Canadian-French) Codepage PC865 (Nordic) Codepage PC852 (Eastern Europe) Codepage PC866 (Russian) Codepage PC857 (Turkish) Windows Codepage Space Page (For user setting) [Default] [See Also] [Sample Program] This is a character code table specified with DIP Switch. CHARACTER CODES TABLE" LPRINT CHR$(&H1B) + "t" + CHR$(0); LPRINT "n"=0; FOR C=&HB2 TO &HB5 LPRINT CHR$(C); NEXT C LPRINT CHR$(&HA); LPRINT CHR$(&H1B) + "t" + CHR$(9); LPRINT "n"=9; FOR C=&HB2 TO &HB5 LPRINT CHR$(C); NEXT C LPRINT CHR$(&HA); END n=0 n = 0 [Print Results] n= 9 23'µ -- 93 -- n = 9 ESC { n [Function] [Code] [Range] [Outline] Specifying/Canceling the inverted characters <1B>H<7B>H<n> 0 n 255 Specifying/canceling inverted characters. Specifying inverted characters. [Caution] · Inverted printing means printing the line turned 180°. · This command is valid only when it is specified at the beginning of a line. · The settings of this command have no effect on PAGE MODE, but items set in PAGE MODE are valid even after STANDARD MODE resumes. [Default] [Sample Program] n=0 LPRINT CHR$(&H1B) + "{" + CHR$(0); LPRINT "AAAAA" + CHR$(&HA); LPRINT "BBBBB" + CHR$(&HA); LPRINT CHR$(&H1B) + "{" + CHR$(1); LPRINT "AAAAA" + CHR$(&HA); LPRINT "BBBBB" + CHR$(&HA); END [Print Results] AAAAA BBBBB Inversion Specified Inversion Canceled Paper Feed Direction -- 94 -- AAAAA BBBBB GS !n [Function] [Code] [Range] Specifying the character size <1D>H<21>H<n> 0 1 1 [Outline] n 255, where: 8, 8 vertical magnification horizontal magnification Specifies the character size (Vertical and horizontal magnification). Bit 0 1 2 3 4 5 6 7 Function Value Hex. Number Decimal Number Refer to Table 2, "Vertical Magnification". Vertical magnification specification Horizontal magnification specification Refer to Table 1, "Horizontal Magnification". Table 1 Horizontal Magnification Hex. Decimal 00 0 10 16 20 32 30 48 40 64 50 80 60 96 70 112 Magnification 1 ×(Standard) 2 ×(Double width) 3× 4× 5× 6× 7× 8× Table 2 Vertical Magnification Hex. Decimal 00 0 01 1 02 2 03 3 04 4 05 5 06 6 07 Magnification 1 ×(Standard) 2 ×(Double height) 3× 4× 5× 6× 7× 8× 7 [Caution] · This command works for all ANK characters except for HRI characters. · This command is ignored if either the vertical magnification or horizontal magnification is out of the defined range. · In STANDARD MODE, the vertical direction is defined as the paper feed direction, and the horizontal direction is defined as the direction perpendicular to the paper feed. These definitions are, therefore, interchanged when 90 -right-turned characters are specified. · In PAGE MODE, the vertical direction means the top-bottom direction of each character. The horizontal direction means the side-to-side direction of each character. -- 95 -- · If characters of different vertical magnification are contained in a line, the baseline of each character is lined up. · Horizontal and vertical magnification can also be specified/ canceled by ESC !. [Default] [See Also] n=0 ESC ! -- 96 -- GS $ nL nH [Function] [Code] [Range] Specifying the absolute vertical position of characters in PAGE MODE <1D>H<24>H<nL><nH> 0 0 [Outline] nL nH 255 255 This command is used in PAGE MODE to specify the vertical position of characters at the data mapping start position as an absolute value measured from the start point. [. . . ] Dieses Signal kann auch als Rücksetzungssignal nach Ändern der DIP-Schalterstellung verwendet werden (siehe 5. 2 "DIP-Schaltertabelle"). Wenn die Pulsbreite des Signals 1 ms oder länger beträgt, wird eine Rücksetzungssignal übertragen. (5) INIT Dieses Signal kann als Rücksetzungssignal verwendet werden, nachdem Sie die Stellung des entsprechenden DIP-Schalters geändert haben (siehe 5. 2 "DIPSchaltertabelle"). Wenn die Pulsbreite des Signals im Leerzeichenzustand 1 ms oder länger beträgt, wird ein Rücksetzungssignal übertragen. [. . . ]