User manual CITIZEN IDP-3221

[. . . ] iDP3221 User's Manual Declaration of Conformity Manufacturer's Name : Manufacturer's Address : Japan CBM Corporation : CBM Bldg. , 5-68-10, Nakano, Nakano-ku Tokyo, 164-0001, Japan Declare the Product Product Name Model Number(s) Line Thermal Printer iDP3221 Series (iDP3221RF, iDP3221PF) (S. No. 9990001 ~ ) Conform to the following Standards LVD EMC : EN60950 : EN55022 : EN61000-3-2 : EN61000-3-3 : EN55024 : EN61000-4-2 : EN61000-4-3 : EN61000-4-4 : EN61000-4-5 : EN61000-4-6 : EN61000-4-8 : EN61000-4-11 : A11: 1997 : 1998 Class A : 1995 : 1995 : 1995 : 1995 ±4KV CD, ±8KV AD : 1995 3V/m, 80MHz-1000MHz AM1KHz 80% : 1995 ±1. 0KV (AC mains), ±0. 5KV (Signal Lines) : 1995 ±1KV Normal mode, ±2KV Common mode : 1996 3V, 0. 15MHz-80MHz AM1KHz 80% : 1993 50Hz, 3A/m (Out of scope) : 1994 10 ms/95%, 500 ms/30%, 5000 ms/100% Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336EEC, 92/31/EEC, 93/68EEC" Place Date Tokyo, Japan August. 1999 Full Name : Position : Europe Contact : Mikio Moriya General Manager R & D Department Signature Norco Declaration AB Box 7146 S-250 07 Helsingborg Sweden Warning This is a Class A products. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This declaration is applied only for 230V model. CITIZEN iDP3221 User's Manual IMPORTANT SAFETY INSTRUCTIONS · · · · · · Read all of these instructions and save them for future reference. Slots and openings on the back or bottom of the case are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. [. . . ] n 1, 49 2, 50 3, 51 Type ID Bit 0 1 2 3 4 5 6 7 Meaning Equipped for 2-byte code support Equipped with autocutter Undefined Undefined Unused Undefined Undefined Unused Hex. 01 02 -- -- 00 -- -- 00 Decimal 1 2 -- -- 0 -- -- 0 Type of printer ID Model ID Type ID ROM version ID Specification Value (hex) iDP3221 20 See table below "Type ID" As per ROM version [Function] [Code] [Range] [Outline] [Caution] · Under DTR/DSR control, the printer sends the printer ID after verifying that the host is ready to receive. If the host is not ready to receive, the printer waits for the host to become ready to receive. · Under XON/OFF control, the printer sends the printer ID without checking whether the host is ready to receive or busy. · Because this command is executed when data is mapped in the receive buffer, there may be a delay between command receiving and printer ID sending depending on the condition of the receive buffer. · If ASB (automatic status back) is enabled by GS a, the host must discriminate between the printer ID due to this command and the status due to ASB. 90 CITIZEN iDP3221 User's Manual GS L nL nH Setting the left margin <1D>H<4C>H<nL><nH> 0 nL 255 0 nH 255 This command sets the left margin specified by nL and nH. [(nL + nH ( 256) ( basic calculation pitch] inches. Printable Area [Function] [Code] [Range] [Outline] The value of the left margin is Left Margin Print Area Width [Caution] · This command only works when it is entered at the beginning of a line. · When Page mode is selected, this command only executes the internal flagging of the printer. · The maximum settable left margin is equal to the horizontal printable area. Once defined, the left margin is not changed if the basic calculation pitch is changed by GS P. · The left margin is calculated with the horizontal basic calculation pitch (x). A fraction resulting from the calculation is corrected with the minimum pitch of the mechanism, and the remainder is omitted. · When mapping character data, if the current print area is not wide enough to accommodate one character of the current font, only the line for that character data is handled as follows: (1) The print area is extended toward the right to be equivalent to one character of the current font, but not wider than the printable area. (2) If one character of the area cannot be provided as a result of step (1), the print area is extended toward the left (so that the left margin is decreased). · When mapping non-character data (bit image, downloaded bit image, or bar code), if the current print area is narrower than 9 bits, only the line for that data is handled as follows: (1) The print area is extended toward the left (so that the left margin is decreased) until it is 9-dot wide, but not wider than the printable area. [Default] [See Also] nL = 0, nH = 0 GS P, GS W 91 CITIZEN iDP3221 User's Manual GS P x y Specifying the basic calculation pitch <1D>H<50>H<x><y> 0 x 255 0 y 255 This command sets the horizontal basic calculation pitch to approx. 25. 4/x mm (1/x inches), and the vertical basic calculation pitch to approx. · If x = 0, the horizontal basic calculation pitch is reverted to the default value. · If y = 0, the vertical basic calculation pitch is reverted to the default value. [Function] [Code] [Range] [Outline] [Caution] · The horizontal direction is defined as the direction perpendicular to the paper feed, and the vertical direction is defined as the paper feed direction. · In Standard mode, the following parameters are used regardless of the character orientation (e. g. (1) Commands using x: ESC SP, ESC S, ESC ¥, GS L, GS W (2) Commands using y: ESC 3, ESC J · In Page mode, the parameters used depend on the character orientation; as follows: (1) If the start point specified by ESC T is the top left or bottom right (the characters are mapped in the direction perpendicular to the paper feed). ·Commands using x: ·Commands using y: ESC SP, ESC $, ESC W, ESC ¥ ESC 3, ESC J, ESC W, GC S, GS ¥ (2) If the start point specified by ESC T is the top right or bottom left (the characters are mapped in the paper feed direction). [. . . ] 9) Nach der Übertragung eines Datenbytes signalisiert der Drucker dem Host-Computer, ob weitere Daten zur Übertragung vorliegen. Wenn der Host-Computer feststellt, daß keine weiteren Daten vom Drucker kommen, wählt der Host-Computer einen der folgenden drei Stati: 1. Durchführung der Terminierung und Rückkehr in den Kompatibilitätsmodus 2. Setzen von HostBusy (nAutoFd) auf Low und Wechsel in die Phase "Reverse Idle" (Event 7) 10) Wenn der Drucker weitere Daten senden will, wählt der Host-Computer einen der folgenden drei Stati: 1. [. . . ]