User manual CITIZEN IDP-3210

[. . . ] LINE THERMAL PRINTER MODEL iDP3210 iDP3210 User's Manual Declaration of Conformity Manufacturer's Name : Manufacturer's Address Declare the Product Product Name Model Number(s) : Japan CBM Corporation : CBM Bldg. , 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Thermal Printer iDP3210 Series (iDP3210R, iDP3210P) (S. No. 0090001 ~ ) Conform to the following Standards LVD EMC : EN60950 : EN55022 : EN61000-3-2 : EN61000-3-3 : EN55024 : EN61000-4-2 : EN61000-4-3 : EN61000-4-4 : EN61000-4-5 : EN61000-4-6 : EN61000-4-8 : EN61000-4-11 : A4:1997 : 1998 Class A : 1995+A1:1998+A2:1998 : 1995 : 1998 : 1995 ±4KV CD, ±8KV AD : 1996 3V/m, 80MH-1000MHz AM 1KHz 80% : 1995 ±1. 0KV (AC Mains), ±0. 5KV (Signal Lines) : 1995 ±1KV (Normal mode), ±2KV (Cmmon mode) : 1996 3V, 0. 15MHz-80MHz AM 1KHz 80% : 1993 50Hz, 1A/m : 1994 0%, 5000ms/ 70%, 500ms/ 0%, 10ms Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336EEC, 92/31/EEC, 93/68EEC" Place Date Tokyo, Japan September, 2000 Full Name: Mikio Moriya Position: General Manager R & D Department Europe Contact : Signature Norco Declaration AB Box 7146 S-250 07 Helsingborg Sweden Warning : This is a Class A products. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This declaration is applied only for 230V model. CITIZEN iDP3210 User's Manual IMPORTANT SAFETY INSTRUCTIONS · · · · · · Read all of these instructions and save them for future reference. Slots and openings on the back or bottom of the case are provided for ventilation. [. . . ] Error Detail POWER LED Memory check error Display pattern ERROR LED Illuminated Not possible Resetting Method (Quick blinking) Cover open Print Head overheat Paper near end Illuminated Illuminated Illuminated Illuminated Illuminated Illuminated Close the cover Automatically recovered when cooled. Set new paper Paper end Illuminated Set new paper (Quick blinking) Cutter motor lock Illuminated Eliminate paper jam (Quick blinking & slow blinking) Macro execution wait Illuminated Press FEED switch. (slow blinking) Details of error Cover open : When printer cover is opened, printer cover open sensor detects the cover opening and has ERROR LED illuminate, then stops printing operation. But, depending on dip switch setting, paper feed can be performed when printer cover is opened. 17 CITIZEN iDP3210 User's Manual Print Head overheat : To protect print head from excessive heat, in case the temperature of print head goes high(approx. 65°C or over), head temperature sensor works and has ERROR LED illuminate, then stops printing operation. 60°C or less), printing operation automatically starts. Paper near end : When the remaining of roll paper goes scarce, paper near end sensor located on the side of roller portion of the upper cover works, and has ERROR LED illuminate to show the remaining of roll paper is getting scarce. (See "setting of paper end detector effective for outputting a signal for no paper" and "setting of paper end sensor effective for print stop" in the chapter of print control function. ) Paper end : When the roll paper runs out completely, the paper sensor located in the paper course near to print head detects the end of print paper and has ERROR LED illuminate, then stops printing operation. (See "setting of paper end sensor effective for outputting a signal for no paper" and "setting of paper end sensor effective for print stop" in the chapter of print control function. ) When the paper is inserted into the paper course near to print head, roll paper is automatically loaded. Cutter motor lock : In case that cutter position sensor locates in the auto cutter unit keeps ON or OFF for one second or more during the operation of cutter motor, this sensor detects it as motor lock state. (See the chapter of 4. 5 "cancellation of cuter lock") (3) FEED Switch With this pressed once shortly, paper is fed by one line. With this kept pressed, lines are fed continuously. In case of macro execution wait, this is executed by pressing FEED switch. (4) FEED Switch and Power Switch By turning ON power switch with pressing FEED SWITCH, , self printing is performed. 18 CITIZEN iDP3210 User's Manual 5. 5. 1 Dip Switch Setting Location of Dip Switch (1) Turn OFF the power switch. (Remove it by taking off two screws at the botto m and turning the cover in the arrowed direction. ) 19 CITIZEN iDP3210 User's Manual 5. 2 Dip Switch Setting DS1 DS1-1 DS1-2 DS1-3 DS1-4 DS1-5 DS1-6 DS1-7 DS1-8 DS1-9 DS1-10 Function Paper cutter Cover open CR switching Unused Print columns International Characters International Characters International Characters Print density Print density ON Enabled Disabled LF activate 44 columns OFF Disabled Enabled Ignored 42 columns Factory Setting ON OFF OFF OFF ON OFF OFF OFF OFF ON See the table below. See the table below DS2 DS2-1 DS2-2 DS2-3 DS2-4 DS2-5 DS2-6 DS2-7 DS2-8 Function Bit length Parity Odd/even DTR/XON-XOFF BAUD RATE BAUD RATE BAUD RATE Unused ON 7 bits Provided Even XON-XOFF OFF 8 bits Not provided Odd DTR/DSR See the table below. ------------------ Factory Setting OFF OFF OFF OFF OFF ON ON OFF (Note) DS2 is available only for serial interface. Print Density DS1-9 DS1-10 Light OFF OFF Standard ON OFF Dark OFF ON Darker ON ON International Character DS1-6 DS1-7 DS1-8 BAUD RATE DS2-5 DS2-6 DS2-7 U. S. A. OFF OFF OFF 150 OFF OFF OFF France ON OFF OFF 300 ON OFF OFF Germany OFF ON OFF 600 OFF ON OFF U. K. ON ON OFF 1200 ON ON OFF Denmark I OFF OFF ON 2400 OFF OFF ON Sweden ON OFF ON 4800 ON OFF ON Italy OFF ON ON 9600 OFF ON ON Japan ON ON ON 19200 ON ON ON 20 CITIZEN iDP3210 User's Manual 6. 6. 1 INTERFACE (Connecting with Peripheral Equipment) Parallel Interface 8 bit parallel signal (DATA 1 ~ 8) ACK , BUSY , STB , FAULT , PE , RESET Printer side 57LE-40360 (Equivalent to amphenol ) 6. 1. 1 Specifications Data input method : Control signals: Applicable connector : 6. 1. 2 Connectoe's Pin Configuration No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Signal Name STB DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 DATA 8 ACK BUSY PE +5V DC No. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Signal Name TWISTED PAIR GND GND FRAME GND RESET FAULT GND Drawer switch output +5V DC 21 Cable side 57-30360 ( ) CITIZEN iDP3210 User's Manual 6. 1. 3 I/O SIGNALS (1) Input Signals to the Printer · DATA : 8-bit parallel signal (positive logic) · STB : Strobe signal to read 8-bit data (negative logic) · RESET : Signal to reset the entire printer (negative logic) 1m sec or more (2) Output Signals from Printer · ACK : An 8 bit data request signal. (negative logic) · BUSY : The signal to indicate BUSY state of the printer. (positive logic) · FAULT : The signal which is made "LOW" when the printer is in alarm state. All the control circuits inside the printer are stop ped at this time. (negative logic) · PE : The signal which is output when paper runs out or goes scarce. (positive logic) · Drawer Switch Output : With the switch open, this signal goes "HIGH". (3) Power supply · +5 V DC · GND : This is 5V pulled up by a 3. 3k resistor. [. . . ] m 0 1 2 3 Mode Name Normal mode Double wide mode Double high mode Double wide/double high mode Dot Density in Vertical Direction 156 DPI 156 DPI 78 DPI 78 DPI Dot Density in Horizontal Direction 154 DPI 77 DPI 154 DPI 77 DPI · When data exist inside the print buffer, this command is ignored. · When a download bit image has not been defined, this command is ignored. · A portion of a download bit image exceeding one line length is not printed. · A download character and a download bit image cannot be defined simultaneously. [. . . ]