User manual CITIZEN IDP-3110

[. . . ] DOT MATRIX PRINTER MODEL iDP3110 iDP3110 User's Manual Declaration of Conformity Manufacturer's Name : Manufacturer's Address : Japan CBM Corporation : CBM Bldg. , 5-68-10, Nakano, Nakano-ku, Tokyo, 164-0001, Japan Declare the Product Product Name Model Number(s) Dot Matrix Printer iDP3110 Series (iDP3110R, iDP3110P) (S. No. 0090001 ~ ) Conform to the following Standards LVD EMC : EN60950 : EN55022 : EN61000-3-2 : EN61000-3-3 : EN55024 : EN61000-4-2 : EN61000-4-3 : EN61000-4-4 : EN61000-4-5 : EN61000-4-6 : EN61000-4-8 : EN61000-4-11 : A4:1997 : 1998 Class B : 1995+A1:1998+A2:1998 : 1995 : 1998 : 1995 ±4KV CD, ±8KV AD : 1996 4. 5V/m, 80MHz-1000MHz AM 1KHz 80% : 1995 ±1. 0KV(AC Mains), ±0. 5KV(Signal Lines) : 1995 ±1KV (Normal mode), ±2KV (Common mode) : 1996 3V, 0. 15MHz-80MHz AM 1KHz 80% : 1993 50Hz, 3A/m : 1994 0%, 5000ms/ 70%, 500ms/ 0%, 10ms Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336EEC, 92/31/EEC, 93/68EEC" Place Date Tokyo, Japan September, 2000 Full Name Position Europe Contact : : Mikio Moriya : General Manager R & D Department Signature Norco Declaration AB Box 7146 S-250 07 Helsingborg Sweden This declaration is applied only for 230V model. CITIZEN iDP3110 User's Manual IMPORTANT SAFETY INSTRUCTIONS * Read all of these instructions and save them for later reference. * Slots and openings on the cabinet and the back or bottom are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. [. . . ] 1. 6 × 2. 4 mm 1. 08 × 2. 4 mm 3. 52 mm Paper Roll 57. 5 ± 0. 5(W) × 60 (Dia) mm 57. 5 ± 0. 5(W) × 80 (Dia) mm Type P: Parallel Interface (Centronics) Type R: Serial Interface (RS-232C) Exclusive ribbon cassette Purple print : IR-91P Black print : IR-91B (Option) DC 7V ± 1V (Printing) Use exclusive adapter (DC 7V, 1. 2A) Printing : approx. (2) Press down on the Ribbon cassette while inserting the ribbon between the printing head and the platen. (3) Wind up the ribbon slack by turning the knob in the direction of the arrow. CITIZEN 8 iDP3110 User's Manual 4. 4 Setting Paper Remove the printer cover. Ensure that the end of the paper is straight or incline as indicated in the diagram. After turning ON the printer, press the LF switch until 5 to 6 cm of paper is fed out of the printer mechanism. Insert paper after moving aside the paper holder in the direction of the arrow. (6) Then, attach the printer cover so the end of the paper comes out of the opening in the cover. (1) (2) (3) (4) (5) CITIZEN 9 iDP3110 User's Manual 4. 5 Self Test Printing A self-printing function is incorporated in this product to enable the printer to check itself. (2) Ensure that the ribbon cassette is attached correctly and turn the power OFF. 4. 6 General Notices (1) Never operate your printer without loading paper and ribbon cassette. Any printing without paper and ribbon cassette may cause damage to printer head. (3) Be careful not to drop any foreign matters, such as paper clips and pin and the like into your printer. (5) Place your printer always on a stable desk which is set horizontal. (6) No organic solvent (thinner, benzin or the lie) shall be used in sweeping clean the surface of the main body case. (7) Make sure that the power of the printer is turned off whenever you do the following. 2) Replacing the ribbon cassette. CITIZEN 10 iDP3110 User's Manual 5. PARALLEL INTERFACE 5. 1 Specifications a) Data input system b) Control signal c) Compatible Connector : 8 bit parallel (DATA 1-8) : ACK, BUSY, STB, RESET, SELECT : Printer side : 57LE-40360 (AMPHENOL or equivalent) : Cable side : 57-30360 (AMPHENOL or equivalent) 5. 2 Connector Pin Assignment PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 SIGNAL NAME STB DATA 1 2 3 4 5 6 7 8 ACK BUSY GND SELECT GND GND FRAME GND PIN 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 SIGNAL NAME TWISTED PAIR GND GND RESET GND CITIZEN 11 iDP3110 User's Manual 5. 3 Description of Input / Output Signals (1) Input signal All input signals utilize type 74HC of CMOS and can be used in TTL level as the input is pulled up with 3. 3 k resistance. - DATA 8 bit parallel signal (positive logic) - STB Strobe signal for reading out data (negative logic) - RESET Signal for resetting the entire unit (negative logic 4ms or more) (2) Output signal TTL is utilized for all output signals. ACK is issued at the end of the BUSY signal (negative logic) - BUSY Signal indicating the printer is busy. Input new data when the signal is in "LOW" condition. (positive logic) - SELECT Signal indicating the printer is set to a selected condition (on-line). Equivalent to "case ground". · Input [ Printer side ] [ Host side ] DATA : 74HC373 equivalent STB : 74HC14 equivalent RESET : 74HC04 equivalent CITIZEN 12 iDP3110 User's Manual · Output [ Printer side ] [ Host side ] (4) Timing chart 1) Timing for data entry and printing T1 T2, T3 T4 0. 5 µs MIN 1 µs MIN 2 µs TYPE (5) Data receiving Printer is capable of accepting data from the host while the BUSY signal is in the "LOW" state. Printer cannot accept data when the signal is "HIGH". CITIZEN 13 iDP3110 User's Manual 6. [. . . ] However, if a new pattern is registered in an address already in use, existing data is cleared and the newly entered data becomes valid. If more than 8 characters are registered, all existing character registration is cleared. [Address setting] Specified address is matched to the character code and can be accessed likewise to the stored fixed character record. If a fixed character is defined in the specified address, the fixed character becomes invalid. [. . . ]