User manual CITIZEN CT-S310

[. . . ] This printer conforms to the following Standards: This declaration is applied only for 230V model. Company names and product names in this manual are trademarks or registered trademarks of relevant companies. IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. [. . . ] To release, refer to "Removing Jammed Paper" in this manual. A cross connection may damage the printer's internal electronics or the host system's hardware. Only use the printer with devices that have designated solenoid specifications for the cash drawer interface connector. To prevent injury and printer failures from worsening, observe the following: Do not touch the printing surface of the thermal head. , paper cutter, gears, active electrical parts) while the printer is working. Be careful that the paper cover does not entrap your hands or fingers. If the printer emits smoke, an odd smell, or unusual noise while printing, immediately abort the current print session and unplug the printer from the supply outlet. When cleaning the printer, always turn it off and unplug it from the supply outlet. Never use organic cleaning solvent such as alcohol, paint thinner, trichloroethylene, benzene, or ketone. When transporting the printer, remove the roll paper form its paper holder. The thermal head is at a dangerously high temperature immediately after printing. The CT-S310 is a thermal line printer designed for use with a broad array of terminal equipment including, data, POS, and kitchen terminals. With extensive features, it can be used in a wide range of applications. When unpacking the printer, confirm that the following are provided: Printer: AC adapter (AC adapter type): AC power cord: Sample paper roll: Partition for 58-mm wide paper roll: User's manual (This manual): 1 1 1 1 roll 1 1 AC adapter (AC adapter type) Printer (AC adapter type) AC power cord Partition for 58-mm wide paper roll Sample paper roll Printer (Built-in power supply type) The printer models are classified by the following designation method: Power supply No marking: AC power type (built-in power supply) DC: DC power supply type Interface RS: Serial RS-232C compliant PA: Parallel IEEE 1284 compliant UB: USB Black mark sensor for back side None: No sensor M1: Left black mark sensor M2: Right black mark sensor Body case color WH: Cool white BK: Black Inducing ground(Character+AC power cord) J: Japan E: Europe U: North America 2 Model Classification) Print method Print width Dot density Print speed Number of print columns *2 ( ) shows the value with 58 mm wide paper. Line thermal dot print method 72 mm/576 dots, (48 mm/384 dots) *1 8 × 8 dots/mm (203 dpi) 150 mm/s (Fastest, print density level 0), 1200 dot lines/s Font A: 48/42 (32/30) columns; 12 × 24 dots Font B: 64/56 (42/40) columns; 9 × 17 dots Font C: 72/63 (48/45) columns; 8 × 16 dots Font A: 1. 23 mm (1/6 inch) Thermal paper roll: 80 -1 mm/58 -1 mm × 83 mm Paper thickness: 65-75 µm Serial (RS-232C compliant), Parallel (IEEE 1284 compliant), USB 2 cash drawers are supported. Orient the cash drawer cable connector correctly, insert it into the cash drawer interface connector on the back of the printer. Connect the drawer`s ground line to the printer`s ground terminal with a screw. Do not connect any other device than the specified cash drawer to the cash drawer interface connector. In case of a built-in power supply type, remove the power box unit before connection. 1 2 3 4 5 6 Signal FG DRAWER 1 DRSW VDR DRAWER 2 GND Function Frame Ground Drawer 1 drive signal Drawer switch input Drawer drive power supply Drawer 2 drive signal Common ground on circuits 5 V, "H" = 3 to 5 V (3) DRSW signal 5V VDR DRSW signal status can be tested with 1 the DLE+EOT, GS+a, or GS+r command or 2 at pin 34 on the parallel interface port. The output current should be kept at 1A or less; otherwise, breakdown or burning could occur. [. . . ] Lighting and blinking status of each error including the above is shown below. Status Paper-end Paper near-end Cover open error Cover open error *1 Cutter lock error Head overheat error Memory check error Low voltage error High voltage error Sum check error Macro execution wait *2 Black Mark detection error Lights Lights O Lights Lights POWER Lamp Lights Lights Lights Lights Lights Lights Turning off ERROR Lamp Lights Lights Lights O O O Buzzer O Memory switches can be set manually or by a command. Manual Setting of Memory Switch (Memory SW) The memory switch can be selected, changed, or written by the combination of three actions: pressing the FEED switch, pressing and holding the FEED switch, and opening or closing the paper cover. With the FEED button pressed and held, turn the printer power on, and then press the FEED button twice. [. . . ]