User manual CITIZEN CT-S300

[. . . ] This printer conforms to the following Standards: This declaration is applied only for 230V model. Company names and product names in this manual are trademarks or registered trademarks of relevant companies. IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. [. . . ] To release, refer to "Removing Jammed Paper" in this manual. A cross connection may damage the printer's internal electronics or the host system's hardware. Only use the printer with devices that have designated solenoid specifications for the cash drawer interface connector. To prevent injury and printer failures from worsening, observe the following: G Do not touch the printing surface of the thermal head. , paper cutter, gears, active electrical parts) while the printer is working. G Be careful that the paper cover does not entrap your hands or fingers. If the printer emits smoke, an odd smell, or unusual noise while printing, immediately abort the current print session and unplug the printer from the supply outlet. G When cleaning the printer, always turn it off and unplug it from the supply outlet. G Never use organic cleaning solvent such as alcohol, paint thinner, trichloroethylene, benzene, or ketone. G When transporting the printer, remove the roll paper form its paper holder. The thermal head is at a dangerously high temperature immediately after printing. The CT-S300 is a thermal line printer designed for use with a broad array of terminal equipment including, data, POS, and kitchen terminals. With extensive features, it can be used in a wide range of applications. When unpacking the printer, confirm that the following are provided: G Printer: G AC adapter (AC adapter type): G AC power cord: G Sample paper roll: G Partition for 58-mm wide paper roll: G User's manual (This manual): 1 1 1 1 roll 1 1 AC adapter (AC adapter type) Printer (AC adapter type) AC power cord Partition for 58-mm wide paper roll Sample paper roll Printer (Built-in power supply type) The printer models are classified by the following designation method: Interface R: Serial RS-232C compliant P: Parallel IEEE 1284 compliant U: USB Character set F: International Black mark sensor for back side None: No sensor (Standard) M1: Left black mark sensor M2: Right black mark sensor Power supply A: AC adapter type S: Built-in power supply type Power cord specification 100: For AC 100V 120: For AC 120V 230: For AC 230V Print method Print width Dot density Print speed Number of print columns *2 ( ) shows the value with 58 mm wide paper. Line thermal dot print method 72 mm/576 dots, (48 mm/384 dots) *1 8 × 8 dots/mm (203 dpi) 130 mm/s (Fastest, print density level 0), 1040 dot lines/s Font A: 48/42 (32/30) columns; 12 × 24 dots Font B: 64/56 (42/40) columns; 9 × 17 dots Font C: 72/63 (48/45) columns; 8 × 16 dots Font A: 1. 23 mm (1/6 inch) Thermal paper roll: 80 -1 mm/58 -1 mm × 83 mm Paper thickness: 65-75 µm Serial (RS-232C compliant), Parallel (IEEE 1284 compliant), USB 2 cash drawers are supported. For serial interface cable, use the one with the following connection. Orient the cash drawer cable connector correctly, insert it into the cash drawer interface connector on the back of the printer. Connect the drawer`s ground line to the printer`s ground terminal with a screw. Do not connect any other device than the specified cash drawer to the cash drawer interface connector. In case of a built-in power supply type, remove the power box unit before connection. 1 2 3 4 5 6 Signal FG DRAWER 1 DRSW VDR DRAWER 2 GND Function Frame Ground Drawer 1 drive signal Drawer switch input Drawer drive power supply Drawer 2 drive signal Common ground on circuits 5 V, "H" = 3 to 5 V (3) DRSW signal 5V VDR DRSW signal status can be tested with 1 the DLE+EOT, GS+a, or GS+r command or 2 at pin 34 on the parallel interface port. [. . . ] Setting Memory SW1-1 Power ON Info Memory SW1-2 Buffer Size Memory SW1-3 Busy Condition Memory SW1-4 Receive Error Memory SW1-5 CR mode Memory SW1-6 Reserved Memory SW1-7 DSR Signal Memory SW1-8 Init Signal Memory SW2-1 Reserved Memory SW2-2 Auto Cutter Memory SW2-3 Spool Print Memory SW2-4 Full Col Print Memory SW2-5 Resume aft PE Memory SW2-6 Paper width Memory SW2-7 Reserved Memory SW2-8 NPE Sensor Memory SW3-1 Resum Cttr Err Memory SW3-2 Resum Open Err Memory SW3-3 Parallel 31 Pin Memory SW3-4 Paper Select Memory SW3-5 Column Number Memory SW3-6 No use Memory SW3-7 CBM1000 Mode Memory SW3-8 Open w/Printing Memory SW4-1 Auto Length Memory SW4-2 BM Sensor Memory SW4-3 No use Memory SW4-4 No use Memory SW4-5 No use Memory SW4-6 No use Memory SW4-7 No use Memory SW4-8 Full Cut Cmd 0 (OFF) Send 4k bytes Full/Err Print "?Manual Setting of Memory Switch (Memory SW) The memory switch can be selected, changed, or written by the combination of three actions: pressing the FEED switch, pressing and holding the FEED switch, and opening or closing the paper cover. With the FEED switch pressed and held, turn the printer power on, and then press the FEED switch twice. Selecting memory switch When the FEED switch is pressed short (within 2 seconds), printing occurs in the order of "Memory SW1" "Memory SW2" "Memory SW3" "Memory SW4" "Write/Factory Setting" "Memory SW1" . [. . . ]