User manual CITIZEN CMP-10

[. . . ] G Except explained elsewhere in this manual, do not attempt to service, disassemble or repair this product. G Note that CITIZEN SYSTEMS is not responsible for any damage attributable to incorrect operation/handling or improper operating environments which are not specified in this manual. G Data are basically for temporary use, not stored for a long period or permanently. Please note that CITIZEN SYSTEMS is not responsible for damage or lost profit resulting from the loss of data caused by accidents, repairs, tests or other occurrence. [. . . ] G Before use, confirm that the power receptacle has sufficient capacity. G Do not connect to the power receptacle where multiple connections are used. G Do not step on, tap, or put any object, on the cable of the AC adapter. G Before connecting or disconnecting AC adapter, turn the printer power OFF. CMP-10 is a compact, full featured portable line thermal printer, which can be used in a large variety of job environments ranging from doorto-door sales through small and mid-sized catering establishments, car-rentals, parking lots, field services to on-board sales on land, sea and air. IrDA/Bluetooth communication with a PDA or similar device is useful for business activities at the point of sale or service. Easily worn on the belt it is a highly efficient device for printing plain text and graphic receipts on demand plus logos, bar codes and other graphic elements. High speed and low noise emission of the line thermal printing mechanism. The large-capacity Lithium-ion rechargeable battery allows an extensive amount of printing with a single charge. When unpacking the package, confirm the availability of: G Printer unit: G Sample paper roll: G AC adapter: G User's manual: 1 piece 1 roll 1 piece 1 copy E (European) model G Belt clip kit 1 set (Belt clip, 2 × screws, 2 × rubber feet) Please refer to the Appendix for how to mount belt clip and rubber feet. J: For Japan U: For North America Model CMP-10: Standard model CMP-10BT: Built-in Bluetooth model Feature Printing system Printing speed Printing head Parameters Direct thermal printing 50 mm/sec Total dots: 384 Dot density: 8 dots/mm Printing width: 48 mm ESC/POS commands plus extra commands for specific printer features ASCII Code, Alphanumeric characters, International characters, Windows Code page FONT A: 32 characters/line, FONT B: 42 characters/line FONT A: 12H × 24V, FONT B: 9H × 16V UPC-A/E, JAN(EAN)13/8 columns, ITF, CODE39, CODE128, CODABAR, CODE93 Friction feed 58 ±0. Emulation Characters Characters per line Dot matrix Bar code type Paper feed system Paper width Paper thickness Recommended paper Paper roll maximum diameter Minimum core diameter Interfaces 6k bps (Transfer rate between Bluetooth module only) The communication speed between Bluetooth and the printer is 115. Transfer capacity: Up to +4 dBm (Class 2 & Class 3) Coding: 128 bit Security level: Link Standard PIN specification: Prepared (16 digits) PIN code: Lower 4 digits of the BD address Profile: Serial Port Profile Speed: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps Interface: Bidirectional serial communication Signal level: RS-232C Data lenght: 8 bits Start bit: 1 bit Stop bit: 1 bit Parity: None Flow control: Xon/Xoff Connector: Motorola Star Tac 64 KB Track 1, 2, 3 Power LED: GREEN and RED Charge LED: GREEN and RED Power switch 1, LF switch 1 Paper end sensor, Open cover sensor, Head temperature, Low battery Idle - approximately 2W When printing - approximately 15W Battery type: Li-ion battery pack Cell Voltage: 3. 4 V Battery pack capacity: 2000 mAh Approximately 3 hours by main unit + AC adapter 30, 000 lines (At temperature 20°C, standard setting, alphanumeric slide pattern printing. The number of lines may be changed by such condition as temperature, etc. Battery charging time Maximum lines printed with fully charged battery 5% density, rated energy) Mechanism: 15, 000, 000 lines UL, c-UL, TUV, GS, PSE (AC Adapter only) VccI B, CE Marking, Fcc B 116 (W) × 104 (D) × 63 (H) mm (50 mm paper cover + Mag stripe reader) Approx. 370 g (with battery and belt clip without paper) Serial Cable, Mag Stripe card reader (Factory option) RED/GREEN blinks fast: No paper or cover open. When waiting for reading mag stripe card (When card reading is finished or after 10 seconds, it lights green. ) · While pressing and holding the Power switch to turn the printer off (When releasing the switch after the LED changes to green, the printer power is turned OFF. (3) IrDA interface unit Receives data from host and transmits printer status. (5) Power switch (ON/OFF) Press and hold the Power switch for 1 second to turn the printer power ON. To turn OFF the printer, press and hold the Power switch till the Power LED changes from red to green. [. . . ] If the head temperature returns to 60°C or below, the printer is ready for printing. Immediately after releasing the LF switch the printer will print out a SELF TEST report. At the end of the report, density, auto-power off time, head temperature, battery output voltage, communication mode, baud rate (for serial communication) are printed. The number of marks * in the parentheses aside battery output voltage shows a level of battery charge in 5 steps. [. . . ]