User manual CITIZEN CH-602B

[. . . ] 22°C) 3V DC +10°C +40°C, 30% to 85%RH ­20°C +60°C, 10% to 95%RH 13. 5cm 19. 5cm 74mm(W) × 31mm(D) × 72mm(H) Approx. 140g (including batteries) Type B equipment 2 pcs "AAA" (LR03) alkaline batteries, Instruction manual, Storage case *Specifications and designs may be changed without notice in the event of improvements being made. CLEANING METHOD OF CUFF After cleaning the cuff with a neutral detergent, lightly rinse it with water and let it dry in the air. Also, be careful not to get water into the air hose. - Eng 2 - English GENERAL REMARKS General Remarks on blood pressure measurement · If the cuff is to be deflated quickly, depress "POWER" switch. · The attached cuff is suited for a wrist circumstance of 13. 5cm to 19. 5cm. [. . . ] · Do NOT keep on measuring so many times, as your arm will have built up congestion of blood, and you will not get a valid reading. - Eng 3 - PRECAUTION FOR USE AND MAINTENANCE Precautions for use · If you suffer from heart disease, high blood pressure or other circulatory disease, please consult your doctor first. · If you feel abnormal pressure of the cuff during use or any other irregularity, reduce the pressure by immediately switching off the power or removing the batteries and consult the sales outlet where purchased. · If you think the measured value is abnormal or if measuring makes you feel unwell, discontinue use and consult your doctor. · Measurement of blood pressure may not be possible for someone with a weak pulse or arrhythmia. · If blood pressure is measured repeatedly, an accurate result will not be achieved. · The memory is erased if the batteries are removed for replacement, etc. and a record should be kept of any necessary data. Nature and frequency of maintenance: This products is designed for use over an extended period of time; however, it is generally recommended that it be inspected every two years to ensure proper function and performance. Protect the nature environment: Please help protect natural environment by respecting national and/ or local recycling regulations when disposing of the batteries and the products at the end of their useful lives. Reference European standard: This products complies with EC instructions 93/42/EEC (Medical Device Directive) and with the following standards: EN 1060-1 : 1995 "Noninvasive Sphygmomanometers, Part 1 General Requirements" and EN 1060-3 : 1997 "Noninvasive Sphygmomanometers, Part 3 Supplementary Requirements for Electromechanical Blood-Pressure Measuring Systems". Precautions for maintenance · Do NOT store the blood pressure monitor where it will be exposed to direct sunlight, high temperature (over 60°C), low temperature (below ­20°C), high relative humidity (over 95%) or in a dusty place. · Do NOT expose the blood pressure monitor to under force or vibration, or drop it. · Remove the battery/batteries when not in use for a long period. · NEVER wipe the blood pressure monitor with thinner or benzene, as they may damage it. · When the monitor is very dirty, wipe it clean with a cloth moistened with Sterilizing alcohol or a neutral detergent, and then wipe it with a dry cloth. Do NOT use thinner or benzene. Manufacturer: Name: Address: Premier Precision Ltd. Block E, G-H, 6 th floor, Phase 2, Yip Fat Factory Building, 73-75 Hoi Yuen Road, Kwun Tong, Kowloon, Hong Kong European Representative: Name: Address: WvW elektronische Geräte Vertrieb GmbH. Robert-Koch-Straße 20, D-80538 München, GERMANY - Eng 4 - English INSTALLING THE BATTERIES · To use this unit, you must install batteries, and also if battery mark " will appear on the display, you must change two pieces of " batteries. · After fastening the under hook, close the battery cover. · "LR03" batteries or equivalent is suitable for this blood pressure monitor. · Open battery cover as illustrated. Replace the new two pieces of batteries, matching the (+) and (­) polarities on each battery with the polarity marks on the case. - Eng 5 - MEASUREMENTS 1. Turn Power On SYSTOLICmmHg DIASTOLICmmHg SYSTOLIC mmHg POWER STA RT DIASTOLIC mmHg PULSE/min PULS/min After all display marks are disappeared, the last measured systolic and diastolic blood pressure values are displayed. (Value of the pulse is not memorized nor displayed. ) Memory function works on for approximately one second or during "POWER" switch is depressed. Press the "POWER" switch to turn on. BT SYSTOLICmmHg SYSTOLICmmHg DIASTOLICmmHg DIASTOLICmmHg PULSE/min PULSE/min All display marks appear for approximately one second and buzzer beeps. " mark is appeared and meaIf batteries become weak, " surement is discontinued. After memorized blood pressure value is disappeared, deflation mark "w" appear for approximately one second. - Eng 6 - English SYSTOLICmmHg DIASTOLICmmHg PULSE/min Wrist edge After three short buzzer beeps, the "0" appears on the display. Attaching of Wrist Cuff Wrist cuff Wrap the cuff around your wrist securely. Wrap the cuff around your wrist securely so that there is no space between the wrist and cuff with the edge of wrist cuff pulled. Open the wrist cuff as the figure. Turn left hand palm upwards and wrap the cuff around the wrist so that the display is placed on the side of palm. [. . . ] Subsequent Measurements When more than one reading is desired, wait at least two minutes between reading in order for the blood at wrist flow to return to normal. Then press the "START" switch again. - Eng 9 - DESCRIPTION OF DISPLAY MARKS DISPLAY MARK CONDITION/CAUSE CORRECTIVE ACTION Measurement is begun, but the pressure was insufficient. Repeat measurement again. Appears when the blood pressure could not be measured accurately. (Some noises were detected by the movement of arm during measurement). Repeat measurement again. First, exhaust air from the cuff, reapply the cuff properly and remeasure. [. . . ]