User manual CITIZEN CD-S500

[. . . ] CE marking shows conformity to the following criteria and provisions: Low Voltage Directive (73/23/EEC)/EN60950-1 EMC Directive (89/336/EEC)/EN55022, EN55024, EN61000-3-2 & EN61000-3-3 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. [. . . ] If you are using a model with serial (RS232C) interface specifications, it is always enabled. The printing dot line columns are changed as follows by setting the "Paper Width" of the roll paper used, the "Number of col. Font Select 99 dots 40/33 79 dots 99 dots 42/35 79 dots Space between Printing line characters columns 3 dots 3 dots 2 dots 2 dots 33 columns 40 columns 35 columns 42 columns Full columns 400 dots 386 dots 42/35 are selected: 386 dots Paper feed direction Font Select 99 dots 40/33 79 dots 99 dots 42/35 79 dots Space between Printing line characters columns 3 dots 3 dots 2 dots 2 dots 30 columns 36 columns 32 columns 40 columns Full columns 42/35 are selected: 360 dots Right offset: 40 dots Paper feed direction Font Select 99 dots 40/33 79 dots 99 dots 42/35 79 dots Space between Printing line characters columns 3 dots 3 dots 2 dots 2 dots 25 columns 30 columns 27 columns 33 columns Full columns 300 dots 298 dots 42/35 are selected: 298 dots Right offset: 100 dots Paper feed direction Insert your fingers into the dents at opposite ends of the front cover to open it with both hands. Until a click is heard so that the ribbon is between the paper cut bar and the print head cover. caution Be very careful not to let your hands touch the print head cover when replacing the ribbon cassette. When the print head has become heated, there is a danger of it burning your hand. The following are the types of roll paper that can be used by this printer. Types: 1P roll paper 2P copy roll paper (1 original + 1 copy) 3P copy roll paper (1 original + 2 copies) (2P and 3P copy roll paper are only usable on models equipped with auto cutter and rewinder. 20mm (total thickness) But the total thickness that can be cut is from 0. Pull the rear cover open lever towards The roll paper you are using is 69. Change the paper width by changing the value set as the width using the Soft SW Setting Mode. When setting the roll paper, be careful not to cut your hand on the edge of the paper. Place the roll paper and pull the end Of the roll paper directly towards you as shown in the figure. Hold the center of the roll paper to pull it as straight as possible so that one of the sides of the paper does not slacken. Be very careful not to let the rear cover catch your hands when closing the rear cover. Tear off surplus paper by holding one Side of the end of the roll paper and pulling it towards you. Do not insert any foreign objects such as a paper clip into the cutter unit. Pull the rear cover open lever towards The copy roll paper you are using is 69. Change the paper width by changing the value set as the width using the Soft SW Setting Mode. When setting the roll paper, be careful not to cut your hand on the edge of the paper. Install the copy roll paper and pull the end of the roll paper straight towards you for about 30cm as shown in the figure. Hold the center of the roll paper to pull it as straight as possible so that one of the sides of the paper does not slacken. [. . . ] Rear cover does not open Insert a Phillips screwdriver (+) into the cutter lock cancel use feed hole on the printer and turn it clockwise or counter clockwise. ) Rotate the screwdriver while watching the paper ejection opening and stop turning it when both ends of the blade are fully retracted. If you do, the printer will be damaged and you will be cut by the blade. After turning the knob until the ribbon feeds smoothly, reset the ribbon cassette. [. . . ]