User manual CITIZEN CBM290

[. . . ] CBM-290/291 User's Manual User's Manual Model CBM-290/291 Japan CBM Corporation Information Systems Div. <Important safety instruction> l l l Read all of these instructions and save them for later reference. l Slots and openings on the cabinet and the back or bottom are provided for ventilation. To ensure reliable operation of the product and to protect it form overheating, do not block or cover these openings. The openings should never be blocked by placing the product on a bed, sofa, rug of other similar surface. [. . . ] When new roll paper is set, this signal is canceled and PAPER lamp lights off. When any print data is remaining in print buffer, make sure that printer starts printing the data after new roll paper is set. 3. 9. 2 Mechanical alarm This printer stops printing, stops supplying motor and print head with power and outputs BUSY signal and FAULT (in Parallel interface) signal to host computer, when the motor of printer mechanism is locked , auto paper cutter is locked, or temperature of print head is getting high. To make printer stand-by mode, turn ON power supply after clearing the problem. Make sure that the data which is stored in the buffer is to be cleared due to power supply is turned OFF. Absolutely, do not carry out clearing the problem during power is ON. CITIZEN 21 l Auto paper cutter lock, paper jam. To make printer ready for print, turn ON power again after clearing the problem. In this case, the print data which is remaining inside of print buffer is cleared due to power supply is turned OFF. Print head is pulled down and error signal is cleared, then printer becomes ready for print. l Heating up of print head temperature When temperature of print head is getting high due to continuous printing etc. , printer stops printing. During temperature of print head is high, any operation is not available, keep printer without printing. As soon as temperature of print head goes low, error signal is canceled automatically and printer becomes ready for print. CITIZEN 22 4. Make sure that power is turned OFF before changing Dip switch settings. DIP SWITCH DS1-1 AUTO CUTTER 2 CR SELECTION 3 PRINT DENSITY 4 DTR-DSR/XON-XOFF 5 INTERFACE 6 " 7 " 8 " ON EQUIPPED LF ENABLE STANDARD XON-XOFF OFF NONE LF DISABLE DARKER DTR/DSR FACTORY SETTING OFF = CBM-290 ON = CBM-291 OFF OFF OFF OFF OFF OFF OFF SEE BELOW DS18 OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON 7 OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON 6 OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON 5 OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON INPUT METHOD PARALLEL INPUT SERIAL INPUT " " " " " " " " " " " " " " PARITY -NONE " " " " ODD " " " " EVEN " " " " BAUD RATE -1200 bps 2400 bps 4800 bps 9600 bps 19200 bps 1200 bps 2400 bps 4800 bps 9600 bps 19200 bps 1200 bps 2400 bps 4800 bps 9600 bps 19200 bps Remarks : For CBM-290, It make Error when ON is selected for DS1-1. Some specifications has been selected in factory setting by jumper as follows. Jumper International model International model International character : U. S. A. J1 Short Auto-loading : Enabled J2 Short Input Buffer : 4 K bytes J3 Short Serial communication bit length : 8 bit J4 Short J5 Short J6 Short Short J7 J8 CITIZEN Open 23 5. Connecting connector Configuration of the connector for power and interface which is packed in this box is as follows. Make sure to confirm the following configuration before connecting the connector. 5. 1 Function of each connector pins PIN NO. SIGNAL NAME I/O 1 ­ 3 VCC OUTPUT 4 ­ 6 GND 7 ­ 12 VP INPUT 13 ­ 18 P-GND 19 20 ERROR 21 22 DTR 23 TXD 24 RXD 25 DSR 26 STB 27 BUSY 28 ACK 29 DATA 0 30 DATA 1 31 DATA 2 32 DATA 3 33 DATA 4 34 DATA 5 35 DATA 6 36 DATA 7 37 PE 38 FAULT 39 RESET 40 FUNCTION POWER SUPPLY FOR CIRCUIT (+5V) GND POWER SUPPLY FOR OPERATION(+24V) GND FOR OPERATION Not available OUTPUT ERROR LED OUTPUT (Can be connected directly. ) Not available OUTPUT SERIAL INTERFACE DTR OUTPUT SERIAL INTERFACE TXD INPUT SERIAL INTERFACE RXD INPUT SERIAL INTERFACE DSR INPUT PARALLEL INTERFACE STROBE OUTPUT PARALLEL INTERFACE BUSY OUTPUT INPUT INPUT INPUT INPUT INPUT INPUT INPUT INPUT OUTPUT PARALLEL INTERFACE ACK PARALLEL INTERFACE DATA 0 PARALLEL INTERFACE DATA 1 PARALLEL INTERFACE DATA 2 PARALLEL INTERFACE DATA 3 PARALLEL INTERFACE DATA 4 PARALLEL INTERFACE DATA 5 PARALLEL INTERFACE DATA 6 PARALLEL INTERFACE DATA 7 PARALLEL INTERFACE PE OUTPUT PARALLEL INTERFACE FAULT INPUT PARALLEL INTERFACE RESET Not available Using connector : LY20-40P-DT1-P5 (JAE) or equivalent Applicable connector : LY10-DC40 (JAE) or equivalent CITIZEN 24 5. 2 Precautions 1. For LED ERROR , there is a resister of 330 Ohm on the circuit side to make current value 10 mA. Make sure to supply power to all pins of power supply for circuit and power supply for operation to keep required current capacity. [. . . ] l Relations between the bit image data and the dot defined are shown below: CITIZEN 42 (36) Printing Download Bit Image (GS / m) Code : [1D]h + [2F]h + m * {0 m 3} Data is described in Hex code. l Modes can be selected by m are shown in table for selection with m are shown below. m 0 1 2 3 l l l l MODE NAME Normal mode Double wide mode Double high mode Double wide/double high mode DOT DENSITY IN VERTICAL DIRECTION 203 DPI 203 DPI 101 DPI 101 DPI DOT DENSITY IN HORIZONTAL DIRECTION 203 DPI 101 DPI 203 DPI 101 DPI When data exist inside the print buffer, this command is ignored. When a download bit image has not been defined, this command is ignored. [. . . ]