User manual CITIZEN CBM230

[. . . ] User's Manual LINE THERMAL PRINTER MODEL CBM-230/231 Japan CBM Corporation Information Systems Div. CBM-230/231 User's Manual 1996. 08. 02(10-DCL)15 Declaration of Conformity Manufacturer's Name : Manufacturer's Address : Japan CBM Corporation : 1-1-7, Okubo, Shinjuku-ku, Tokyo 169, Japan Declare the Product Product Name Model Number (s) Thermal Printer CBM230 Series (CBM230R, CBM230P, CBM231R, BM231P (S. NO. 95Y0001 ) Conform to the following Standards LVD EMC : EN60950 : EN55022 : EN61000-3-2 : EN50082-1 : IEC801-2 : IEC801-3 : IEC801-4 :1992+A1+A2:1993 :1994 Class A :1995 :1992 :1991 4KV CD, 8KV AD :1984 3V/m, 27MHz-500MHz :1988 0. 5KV Signal Line 1KV AC mains Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336EEC, 92/31/EEC, 93/68EEC" Signature Place Date Tokyo, Japan November, 1995 Full Name : Koji Tanabe Position : General Manager R & D Department Europe Contact : Europe Liaison Office Kuruisweg 805, Holland Office Center Building 3-2132 NG Hoofddorp, the Netherlands Warning This is a Class A products. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This declaration is applied only for 230V model. CITIZEN 2 CBM-230/231 User's Manual IMPORTANT SAFETY INSTERUCTIONS Read all of these instructions and save them for later reference. l Slots and openings on the cabinet and the back or bottom are provided for ventilation. [. . . ] (1) DTR signal (Refer to 7. 3 1) (2) TD signal (Refer to 7. 3 1) CITIZEN 30 CBM-230/231 User's Manual 7. 3. 6 Electrical Characteristics (1) RS-232C circuit Input (RD, DSR) Output (DTR, TD) CITIZEN 31 CBM-230/231 User's Manual 8 DRAWER KICK CONNECTOR 8. 1 Specifications (1) Drawer kick drive signal The pulses specified by ESC p are output. The state of the switch(+) can be known through the pin 34 of the interface connector when parallel interface is used, and through the ESC u command when the serial interface is used. (2) Electrical characteristics 1) Drive voltage : DC 24 V 2) Drive current : 0. 8 A at maximum(should be within 510 ms) 3) Switch signal : Signal level "L" = 0 to 0. 5 V "H" = 3 to 5 V 8. 2 Connector's Pin Configuration No. 1 2 3 4 5 6 SIGNAL NAME FG DRAWER 1 DRSW VDR DRAWER 2 GND FUNCTION Frame ground Drawer 1 driving signal Drawer SW input Drawer driving power supply Drawer 2 driving signal Common ground on the circuits Connector used Applicable connector : TM5RJ3-66(HIROSE) :Equivalent to TM3P-66P(HIROSE) [Cautions] 1) No output is allowed during printing. Be careful not to use a drawer with a current over 0. 8A to avoid damage to the printer. ) 8. 3 Drive Circuit CITIZEN 32 CBM-230/231 User's Manual 9 PRINT CONTROL FUNCTION 9. 1Control Codes List 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 CONTROL CODE HT CR LF ESC SP !% & * 2 3 @ D E G J R c3 c4 c5 d p t v u { V $ ¥ GS k w h H f * / : ^ ESC = a i m FUNCTION Horizontal tab command Print command Printing and paper feed Setting the right space amount of the character Collective specifying printing mode Specifying/canceling download character set Defining download characters Specifying the bit image mode Specifying/canceling underline Specifying 1/6-inch line feed rate Setting line feed rate n/203 inch Initializing the Printer Setting horizontal tab position Specifying/canceling highlighting Specifying/canceling double printing Printing and feeds paper n/203 inch Selecting the international characters Setting of paper end sensor effective for outputting a signal for no paper(Parallel Mode Only) Setting of paper end sensor effective for print stop Enabling/disabling the panel switches Printing and feeding the paper by n lines Generating the specified pulse(Drawer Kickout) Selecting the character code table Transmitting the printer status(Serial Mode Only) Transmitting the status of peripheral equipment(Serial Mode Only) Specifying/canceling the inverted characters Specifying/canceling the 90°- right-turned characters Specifying the absolute positions Specifying the relative positions Printing the bar code Selecting the horizontal size (scale factor) of bar code Selecting the height of the bar code Selecting the printing position of HRI character Selecting the font of HRI character Defining the download bit image Printing the download bit image Starting/ending macro definition Executing the macro Data input control Aligning the characters Full cut Partial cut CITIZEN 33 CBM-230/231 User's Manual 9. 2Input Data Format (1) Horizontal Tab Command (HT) Code : (09)h Shifts the printing position to the next horizontal tab position. Initial setting of the horizontal tab position is in 9th, 17th, 25th, 33rd, 41st columns of FONT A. (2) Print Command (CR) Code : [0D]h 1) When DS 1 - 8 is OFF: This command is ignored. 2) When DS 1- 8 is ON: With data held inside the input buffer, printing and line feed are performed. Without data inside the input buffer, however, no printing is performed. (3) Printing and Paper Feed Command (LF) Code : [0A]h Prints data inside the internal input buffer and feeds lines based on the line feed amount having been set. (4) Setting the right space amount of the characters (ESC SP) Code : [1Bh] + [20h] + n * {0 < n < 20} Data is described in Hex code. The rightward space amount in double wide mode is made double of the set volume. CITIZEN 34 CBM-230/231 User's Manual (5) Specifying Collectively the Print Mode (ESC !n) Code: [1Bh] + [21h] + n * {0 < n < FF} The data is described in Hex code. Each n bit indicates the following: BIT FUNCTION 0 Font A VALUE 1 0 Character font Font B 1 Undefined 2 Undefined 3 Highlighting Canceled Specified 4 Double height Canceled Specified 5 Double width Canceled Specified 6 Undefined 7 Underline Canceled Specified l With double height and double width being specified simultaneously, double wide and double high characters are consisted. l An underline is attached to the full character width, which, however, is not attached to the part having been skipped by the horizontal tab. (6) Specifying/Canceling Download Character Set (ESC % n) Code: [1B]h + [25]h + n * {0 < n < FF} Data is described in Hex code. Download characters and download bit images cannot be defined simultaneously. The lowest bit (n0) indicates the following: n0= 0: Canceling download character n0= 1: Specifying download character CITIZEN 35 CBM-230/231 User's Manual (7) Defining Download Character (ESC & s n m a (D1D2 -Dn) Code: [1B]h + [26]h + s +n +m +a +Dn * {s = 02} {20 (Hex) n 7E (Hex)} {20 (Hex) m 7E (Hex)} {0 < a < 0A (Hex)} Defines the font of download characters of alphanumeric characters. l "n" indicates the start character code and "m" indicates the end character code. l Character codes definable includes 95 ASCII codes in total between <20>H-<7E>H. l "a" indicates the number of dots in horizontal direction for definition. [. . . ] l When this command is received while in macro definition, suspension of macro definition is indicated. l While in macro execution with n3=1, paper feed with the FEED SW is not available. n3 0 1 Continuous execution CITIZEN 52 CBM-230/231 User's Manual (38) Data Input Control (ESC = n) Code : [1B]h + [3D]h + n * {0 n FF} Data is described in Hex code. l Each bit of n indicates as follows: Device B VALUE IT 0 1 0 Printer Invalid Valid 1 Undefined 2 Undefined 3 Undefined 4 Undefined 5 Undefined 6 Undefined 7 Undefined l When the printer has not been selected, this printer abandons all received data until it is selected by this command. [. . . ]