User manual CITIZEN CBM1000II

[. . . ] In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference. [. . . ] The CBM1000 Type II is a compact thermal line printer designed for use with a broad array of terminal equipment including data, POS, and kitchen terminals. With extensive features, it can be used in a wide range of applications. To obtain the best results from the CBM 1000 Type II printer, please read the instructions this manual thoroughly. Supply/replace paper rolls by simply dropping a paper roll into the printer and closing the cover. Select between an easy-to-handle, built-in power supply type and lightweight flat AC adapter type. When unpacking the printer, confirm that the following are provided: Printer Partition AC power cord (not supplied with Type D) Do not use the printer in an environment where condensation can occur. If condensation forms, leave the power off until it completely evaporates. Do not connect any other device than the specified drawer (Solenoid) to the drawer kick-out connector. Function Frame Ground FG DRAWER 1 Drawer 1 drive signal DRSW Drawer switch input VDR Drawer drive power supply DRAWER 2 Drawer 2 drive signal GND Common ground on circuits 5 V, "H"=3 to 5 V (3) DRSW signal DRSW signal status can be tested with the DLE+EOT, GS+a, or GS+r command or at pin 34 on the parallel interface port. The output current should be kept at 1 A or less; otherwise, breakdown or burning could occur. Placing your hands on both sides of the printer cover, open it until it comes to a stop. Check the winding direction of the paper roll, and then place it into the paper roll holder correctly. Tear bar Print head Printer cover Always use the specified types of paper roll. Use of other types of paper roll may not be able to guarantee the specified print quality or service life of the printer. When opening the printer cover, do not apply an excess force to it beyond its stop position. Push the sensor knob in the direction of arrow 1 to disengage its claw (Or unlock the sensor unit), and then adjust the sensor unit to a desired paper remaining position within the range shown by arrow 2. The following table shows the relationship between adjustment positions and levels of paper roll remaining. (A rough guide) Adjustment position 1 2 3 4 Level of paper remaining (Paper roll outside diameter/mm) * When specified paper rolls are used. Use the level of paper remaining (Paper-roll outside diameter) just as a guide as it varies depending on the particular printer and paper rolls used. Take off damper retention screws, reposition damper (11 mm) in the direction of the arrow, then secure it with the original screws again. Do not change DIP switch setting from 58 mm into 80 mm roll paper in the middle of printing. Do not touch the heating element of the head with a bare hand or metal object either. [. . . ] ) Fine carta: Quando il rotolo di carta è finito , il sensore di fine carta situato vicino alla testina di stampa lungo il percorso di scorrimento della carta rileva la fine del rotolo con la conseguente accensione della spia ERROR e l'arresto della stampa. (Vedere "Selecting the paper sensor valid for paper end signal output" e "Selecting the Paper-Near End Sensor valid for print stop". (Consulte "Selecting the paper sensor valid for paper end signal output" y "Selecting the Paper-Near End Sensor valid for print stop". ) Fin del papel: Cuando se haya agotado el rollo de papel , el sensor del fin del papel , situado cerca de la cabeza impresora en la ruta del papel , detectará el final del rollo del papel , haciendo que se encienda la luz ERROR y se detenga la impresión. [. . . ]