User manual CITIZEN CBM-910II

[. . . ] DOT MATRIX PRINTER MODEL CBM-910 Type II User's Manual WEEE MARK En Ge Fr Sp It Du Da Por Pol CITIZEN is registered trade mark of CITIZEN WATCH CO. , LTD. , Japan CITIZEN es una marca registrada de CITIZEN WATCH CO. , LTD. , Japón ESC/POS is a trade mark of Seiko Epson Corporation. --1-- Declaration of Conformity This printer conforms to the following Standards: Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC. LVD : EN60950-1 EMC : EN55022 EN61000-3-2 EN61000-3-3 EN55024 Class A This declaration is applied only for 230V model. IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference. CAUTION: Use shielded cable for this equipment. Sicherheitshinweis Die Steckdose zum Anschluß dieses Druckers muß nahe dem Gerät angebracht und leicht zugänglich sein. For Uses in Canada This Class A digital apparatus complies with Canadian ICES-003. [. . . ] Using the SEL switch and LF switch, choose one of the options for each setting item. Setting items and options are printed each time the switch is pressed. The SEL switch allows the option being printed to be determined as the set value for current setting item, advancing to the next option item. The LF switch allows the option currently being printed to be deselected among the same setting items and the next option item to be printed. To fix the value set by the memory switch when the option item of the last setting items is selected, press the SEL switch. To restart setting from the first setting items, press the LF switch. b) NOTE Before turning the printer power on, restore the DIP switch No. 4 to the former position. -- 19 -- <Contents of Memory Switch Setting> In square brackets ([ ]), choose one of the options for each setting item. Country (Selecting international character set) [*USA, FRA, GER, U. K, DEN, SWE, ITA, SPE, JPN] Selects a international character set. For international character set, refer to International Character Code Table. JPN = Japan GER = Germany DEN = Denmark Code page (Selecting code page) [CP-437, Katakana, CP-858, CP-860, CP-863, CP-865, CP-852, CP-866, CP-857, Windows, CP-864, CP-869, *910Intl, *910JPN, Space] Selects a code page. Among the character sets for model type, model F is defaulted to 910Intl and model J to 910JPN. CP-437 = Codepage PC437 CP-858 = Codepage PC858 CP-863 = Codepage PC863 CP-852 = Codepage PC852 CP-857 = Codepage PC857 CP-864 = Codepage PC864 910Intl = 910 Emulation (International) Space = Blank page for user's setting Katakana = Katakana CP-860 = Codepage PC860 CP-865 = Codepage PC865 CP-866 = Codepage PC866 Windows = Codepage WPC1252 CP-869 = Codepage PC869 910JPN = 910 Emulation (Japan) 3. Emulation (Selecting 910/3110 Emulation) [*CBM-910, iDP-3110] Sets command system to 910 Emulation or 3110 Emulation. ACK Timing (ACK timing) [Before, Center, *After] *1 ACK output timing for parallel I/F can be changed in 3 steps. Sensor (Enable/Disable paper-near-end) [*Enable, Disable] This setting allows selection between Enable/Disable of paper-near-end sensor. P-ON Sel (Online status at Power ON) [*Select, Deselect] Selects the status of the SEL switch on the operation panel at power ON. 4. 5. 6. -- 20 -- 7. BUSY (Busy signal clear timing) [*Standard, CBM-910] *1 Selects the clear timing of Busy signal for parallel I/F. Buffer [*2k bytes, 72 bytes] Select buffer size. 8. *1: For ACK timing and Busy timing, only setting the parallel board is available. 4. 7 Paper-Near-End, Mechanical Alarm, Memory Error (1) Paper-near-end Printing paper shortage is detected and informed with SEL lamp blinking at 0. 5second intervals, where printing is suspended. At this time, power supply to the motor and printing solenoid is stopped with BUSY signals output in the host computer. To recover from Paper-near-end state, set new paper and press SEL switch twice. (2) Mechanical alarm On occurrence of locked motor, any kind of trouble in the mechanism is suspected. Power supply to the motor and printing solenoid is stopped and BUSY signals are output in the host computer. To recover from alarm state, eliminate the trouble cause and press SEL switch twice. If it is in the course of printing, printing is started at the beginning of the interrupted line. [. . . ] Command for setting to invalid operates regardless of the emulation or number of digits. Registered Characters Enable/Disable Command 910 Emulation (40 digits) 910 Emulation (24 digits) 3110 Emulation (40 digits) 3110 Emulation (24 digits) Set to Valid O × × × Set to Invalid O O O O O: Operation enabled by the Valid/Invalid command of registered characters. ×: As the registered characters are valid by the Register User-defined Character command, it is not necessary to set the registered characters to be valid. -- 43 -- (14) Bit Image Printing (ESC +"K"+ n1 + n2 + n3) Command With ESC (1BH) + K (4BH) + n1 + n2 + n3 code being input, conversion from Text mode into Bit Image mode takes place. The n1/n2/n3 assigns amount of transmission of bit image data which follows these. of bytes in lateral direction and n2 (lowermost)/n3 (uppermost) represent the no. [. . . ]