User manual CITIZEN CBM-820

[. . . ] TERMINAL SLIP PRINTER MODEL CBM-820 User's Manual Declaration of Conformity This printer conforms to the following Standards: Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC. LVD EMC : : : : : EN60950 EN55022 EN61000-3-2 EN61000-3-3 EN55024 Class B This declaration is applied only for 230V model. CITIZEN is a registered trade mark of CITIZEN WATCH CO. , LTD. , Japan CITIZEN es una marca registrada de CITIZEN WATCH CO. , LTD. , Japón ESC/POS and TM-295 are trademarks of SEIKO EPSON CORPORATION Auto Side LoadingTM is a trademark of Star Micronics Co. , Ltd. Windows codepage is a registered trademark of Microsoft Corporation IMPORTANT SAFETY INSTRUCTIONS · Read all of these instructions and save them for future reference. · Do not place this product on an unstable cart, stand or table. · Slots and openings on the back or bottom of the case are provided for ventilation. [. . . ] n is equal to the setting column position - 1, and if the horizontal tab is to be set in the 9th column, for example, set n = 8. · The tab position is set to the position at a distance of the character width × n from the head of the line. This character width includes the right space size of the character, and if double width is selected, the character width will be doubled. A horizontal magnification selection is followed even in the page mode. · The data, <n>k, which denotes a setting position is input in the ascending order and ends with <00>H. · If the data <n>k is equal to or smaller than the preceding data <n>k-1, it is assumed that horizontal tab setting has been finished. If this is the case, the subsequent data will be processed as normal one. · If HT is executed, a move to the tab position beyond the print area will be made to the position of the print area + 1 dot. · Even if the character width is changed after setting the horizontal tab position, the latter will not change. · There are two kinds of right space sizes of the characters; for the standard mode and page mode. To set the horizontal tab position in the respective modes, set the right space size of the characters in the very mode you are in. Every 8 characters of the 5 × 7 font (9th, 17th, 25th character, and so on) HT [Caution] [Default] [See Also] ­ 54 ­ ESC F n [Function] [Code] Selects/Deselects Ejection of Single Sheet in Reverse Direction ASCII Hexadecimal Decimal 0 n 255 ESC F 1B 46 27 70 n n n [Range] [Outline] This command selects or deselects single sheet ejection in the reverse direction with FF. At n = < 0>B, the command deselects reverse directional ejection(selects forward directional ejection). n=0 FF [Default] [See Also] ESC J n [Function] [Code] Print and Paper Feed ASCII Hexadecimal Decimal 0 n 255 ESC J 1B 4A 27 74 n n n [Range] [Outline] This command prints the data in the print buffer and feeds the paper by n/60 inch. Since the printer has the minimum paper feed pitch of 1/144 inch, a paper feed amount of n/60 inch is treated as follows: · For the standard mode: The paper is fed by an approximate value of INT((6n+5)+0. 5)/72 inch. · For the page mode: The paper is fed by n/72 inch(n coordinate). The head of the line is assumed to be the next printing start position. [Caution] ­ 55 ­ ESC K n [Function] [Code] Print and Reverse Paper Feed ASCII Hexadecimal Decimal 0 n 255 ESC K 1B 4B 27 75 n n n [Range] [Outline] This command prints the data in the print buffer and feeds the paper by n/60 inch in the reverse direction. Since the printer has the minimum paper feed pitch of 1/144 inch, n/60-inch reverse directional paper feed is treated as follows: · For the standard mode: The paper is fed by an approximate value of INT((6n+5)+0. 5)/72 inch. · The head of the line is assumed to be the next printing start position. · A set amount does not remain. [Caution] ­ 56 ­ ESC L [Function] [Code] Selects Page Mode ASCII Hexadecimal Decimal ESC L 1B 4C 27 76 [Outline] This command switches from the standard mode to the page mode. · The page mode deploys the received data over the specified print area and prints it in batch with the FF command. Consequently, normal print commands such as LF only deploy the data in the printer's memory, but not actually print it. [. . . ] Die Schalter 1 bis 7 sind werksseitig auf ON gestellt, während die Schalter 8 bis 10 werksseitig auf OFF gestellt sind. Schalter 1 Baudrate 2 3 4 5 6 7 8 9 10 Datenlänge Paritätsprüfung Parität Quittungsaustausch Empfangspuffergröße Zeichencode-Satz Stift 6 (DSR) Rückstellsignal Stift 25 (INIT) Rückstellsignal 8 bits Inaktiv Ungerade DTR/DSR 2 K bytes Japanisch (Katakana) Aktiv Aktiv 7 bits Aktiv Gerade XON/XOFF 35 bytes International (PC437) Inaktiv Inaktiv Siehe untenstehende Tabelle Parameter ON OFF Baudrate 1200BPS 2400BPS 4800BPS 9600BPS Schalter 1 OFF ON OFF ON Schalter 2 OFF OFF ON ON ­ 122 ­ 5. 3 Einstellen der Speicherschalter Jeder Speicherschalter ist ein 16-Bit-Wortspeicher in EEPROM. Einzelheiten über Funktionen und Einstellungen der Speicherschalter siehe "9. Die untenstehende Tabelle zeigt die werksseitigen Einstellungen der Speicherschalter. Speicherschalter #0 #1 #2 #3 #4 #5 Hexadezimalcode ­ ­ ­ ­ 0000 0000 Wichtig!Ein Umstellen der Speicherschalter kann zu Funktionsstörungen des Druckers führen. ­ 123 ­ 6. [. . . ]