User manual CITIZEN CBM-510

[. . . ] · Slots and openings on the back or bottom of the case are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near or over a radiator or heater. [. . . ] · In PAGE MODE, the vertical direction means the top-bottom direction of each character. The horizontal direction means the side-to-side direction of each character. -- 94 -- · If characters of different vertical magnification are contained in a line, the baseline of each character is lined up. · Horizontal and vertical magnification can also be specified/ canceled by ESC !. [Default] [See Also] n=0 ESC ! -- 95 -- GS $ nL nH [Function] [Code] [Range] Specifying the absolute vertical position of characters in PAGE MODE <1D>H<24>H<nL><nH> 0 0 [Outline] nL nH 255 255 This command is used in PAGE MODE to specify the vertical position of characters at the data mapping start position as an absolute value measured from the start point. The vertical position of a character at the next data mapping start position will be at a point [(nL + nH × 256) × basic calculation pitch] inches away from the start point. · Any specification of absolute vertical position out of the print area is ignored. · The horizontal position of a character at the data mapping start position is not moved. · Depending on the start point specified by ESC T, this command acts as follows: (1) If the start point is the top left or bottom right, the command specifies the absolute position in the paper feed direction (The character's top-bottom direction), using the vertical basic calculation pitch (y). (2) If the start point is the top right or bottom left, the command specifies the absolute position in the direction perpendicular to the paper feed (The character's top-bottom direction) using the horizontal basic calculation pitch (x). · Fractions resulting from calculations are corrected with the minimum pitch of the mechanism, and the remainder is omitted. [Caution] [See Also] ESC $, ESC T, ESC W, ESC \, GS P, GS \ -- 96 -- GS * n1 n2 [ d ] n1×n2×8 Defining the download bit image <1D>H<2A>H<n1><n2> [< d >] n1 × n2 × 8 1 1 0 n1 n2 d 255 48 1536 255 [Function] [Code] [Range] n1 × n2 [Outline] Defines download bit images of the number of dots specified by n1 and n2. · The numbers of dots are n1 × 8 in horizontal direction and n2 × 8 in vertical direction. · The black/white inversion works on internal and downloaded characters. · The black/white inversion works also on the right spacing of characters defined by ESC SP. · This command does not affect the bit image, downloaded bit image, bar code, HRI characters, or the skip area specified by HT, ESC $, or ESC \. · Black/white inversion specification takes precedence over underline specification. Underline printing specified is, therefore, nullified if black/white inversion is specified; the underline setting, however, remains unchanged. [Default] n=0 -- 102 -- GS H n [Function] [Code] [Range] Selecting of printing position of HRI characters <1D>H<48>H<n> 0 48 [Outline] n n 3 51 Selecting printing position of HRI characters in printing bar codes. · "n" means the followings. n 0, 48 1, 49 2, 50 3, 51 Printing Position No printing Above the bar code Below the bar code Both above and below the bar code [Caution] · The HRI characters refer to the bar code-turned characters so that you can read them. · The HRI characters are printed in the font selected with GS f. · Specify before the GS k command. [Default] [See Also] [Sample Program] n=0 GS f, GS k LPRINT CHR$(&H1B) + "3" + CHR$(5); LPRINT CHR$(&H1D) + "h" + CHR$(50); LPRINT CHR$(&H1D) + "H" + CHR$(0); GOSUB BC LPRINT CHR$(&H1D) + "H" + CHR$(1); GOSUB BC LPRINT CHR$(&H1D) + "H" + CHR$(2); GOSUB BC LPRINT CHR$(&H1D) + "H" + CHR$(3); GOSUB BC END BC: LPRINT CHR$(&H1D) + "k"; LPRINT CHR$(4); LPRINT "12" + CHR$(0); LPRINT CHR$(&HA); RETURN -- 103 -- [Print Results] No HRI characters Printed above Printed below Printed above and below -- 104 -- GS I n [Function] [Code] [Range] [Outline] Sending the printer ID <1D>H<49>H<n> 1 n 4 , 49 n 52 Sends the specified printer ID. n 1, 49 2, 50 3, 51 4, 52 Type of printer ID Model ID Type ID ROM version ID Label Length Specification Value (Hex. ) CBM1000 30 Refer to table "Type ID" below As per ROM version Depends on label sheet (mm) Type ID If n=2, 50 is specified: Bit 0 1 2 3 4 5 6 7 Meaning Equipped for 2 byte code support Equipped with autocutter Thermosensitive paper Label Label paper(when "Label" is selected) Undefined Unused Undefined Undefined Unused Hex. 01 02 -- -- -- 00 -- -- 00 Label Paper Decimal 1 2 -- -- -- 0 -- -- 0 Black Mark Paper n = 4, 52 specified (only for label specs) The label length and label gap currently used are returned in 4-byte code. Byte 1 + Byte 2 x 256 = Label length (between black mark paper)1 Byte 3 + Byte 4 x 256 = Label gap (black mark paper length)2 [Caution] 1 2 2 1 · Under DTR/DSR control, the printer sends the printer ID after verifying that the host is ready to receive. If the host is not ready to receive, the printer waits for the host to become ready to receive. [. . . ] Hinweis: Die Werte in Klammern gelten für den Fall, daß eine Größe von 72 Byte für den Eingangspufferspeicher mit Hilfe der DIP-Schalter ausgewählt wurde. (4) DSR Wenn die Steuerung per DTR/DSR aktiviert ist, überträgt der Computer während der Übertragung von Statusinformationen Daten an den Drucker, nachdem er geprüft hat, daß es sich bei diesem Signal um ein Leerzeichen handelt. Wenn die Steuerung per DTR/DSR nicht aktiviert ist, ignoriert der Computer dieses Signal und sendet Daten an den Drucker. Dieses Signal kann auch als Rücksetzungssignal nach Ändern der DIP-Schalterstellung verwendet werden (siehe 5. 2 "DIP-Schaltertabelle"). [. . . ]