User manual CITIZEN CBM-270

[. . . ] LINE THERMAL PRINTER MODEL CBM-270 User's Manual CBM-270 User's Manual Declaration of Conformity This printer conforms to the following Standards: Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC, 93/68/EEC. LVD : EN60950 EMC : EN55022 Class A EN61000-3-2 EN61000-3-3 EN55024 This declaration is applied only for 230V model. WARNING : This is a Class A products. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CITIZEN is a registered trade mark of CITIZEN WATCH CO. , LTD. , Japan CITIZEN es una marca registrada de CITIZEN WATCH CO. , LTD. , Japón CITIZEN CBM-270 User's Manual IMPORTANT SAFETY INSTRUCTIONS · · · · · · Read all of these instructions and save them for future reference. Slots and openings on the back or bottom of the case are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, do not block or cover these openings. [. . . ] · An underline is not attached to a 90 °- right-turned characters. · Specification/cancellation with this command is invalid to Kanji. ESC !, FS - LPRINT CHR$ (&H1B) ; "-" ; CHR$ (0) ; LPRINT "AAAAA" ; LPRINT CHR$ (&H1B) ; "-" ; CHR$ (1) ; LPRINT "AAAAA" ; CHR$ (&HA) ; END [Caution] [See Also] [Sample Program] [Print Results] ESC [Code] 2 Specifying 1/6-inch line feed rate <1B> H <32> H The line feed rate per line is specified by 1/6 inch. [Print Results] LPRINT "AAAAA" ; CHR$ (&HA) ; LPRINT CHR$ (&H1B) ; "3" ; CHR$ (0) ; LPRINT "AAAAA" ; CHR$ (&HA) ; LPRINT CHR$ (&H1B) ; "3" ; CHR$ (50) ; LPRINT "AAAAA" ; CHR$ (&HA) ; LPRINT CHR$ (&H1B) ; "2" ; LPRINT "AAAAA" ; CHR$ (&HA) ; LPRINT "AAAAA" ; LPRINT CHR$ (&H1B) ; "J" ; CHR$ (100) ; LPRINT "AAAAA" ; CHR$ (&HA) ; LPRINT "AAAAA" ; CHR$ (&HA) ; END [Function] [Outline] [Sample Program] 40 CITIZEN CBM-270 User's Manual ESC [Code] 3 n Setting line feed rate of minimum pitch <1B> H <33> H <n> 0 n 255 The line feed rate per line is specified by n/360 inch. Since an actual mechanical pitch is 1/203 inch, it is internally converted approximate to the value specified with this command. [Function] [Range] [Outline] [Default] · The initial value is n = 60 (1/6 inch) (18H), being 4. 23 mm line feed rate. [Print Results] See Sample Program and Print Results for ESC 2 on Page 40. [Sample Program] ESC [Code] = n Data input control <1B> H <3D> H <n> 0 n 255 Selecting equipment in which data input from the host is effective. · Each bit of n indicates as follows: Bit 0 1 2 3 4 5 6 7 Equipment Printer Not defined Not defined Not defined Not defined Not defined Not defined Not defined Value 0 Invalid 1 Valid [Function] [Range] [Outline] · When the printer has not been selected, this printer abandons all the received data until it is selected by this command. [Caution] · Even when the printer has not been selected, it can become BUSY state through printer operation. · When the printer is deselected, this printer discards all the data until it is selected with this command. [Default] n=1 [Print Results] LPRINT "AAAAA" ; LPRINT CHR$ (&H1B) ; "=" ; CHR$ (0) ; LPRINT "aaaaa" ; CHR$ (&HA) ; LPRINT CHR$ (&H1B) ; "=" ; CHR$ (1) ; LPRINT "AAAAA" ; CHR$ (&HA) ; END [Sample Program] 41 CITIZEN CBM-270 User's Manual ESC @ Initializing the printer <1B> H <40> H Clears data stored in the print buffer and brings various settings to the initial state (Default state). [Caution] · Data inside the internal input buffer are not cleared. " ; CHR$ (&H30) ; LPRINT CHR$ (&H1B) ; "V" ; CHR$ (1) ; LPRINT "AAA" ; CHR$ (&HA) ; LPRINT CHR$ (&H1B) ; "@" ; LPRINT "AAA" ; CHR$ (&HA) ; END [Function] [Code] [Outline] Each setting has been initialized by the reset command. ESC D [n] k NUL Setting horizontal tab position <1B> H <44> H [<n>] k <00> H 1 n 255 0 k 32 [Outline] Specifying a horizontal tab position. For example, to set the position at 9th column, n=8 is to be specified. · k denotes the number of horizontal tab positions you want to set. · The tab position is set at position where it is "character width x n" from the line beginning. The character width, at this time, includes the rightward space amount. · <n> k, which denotes a setting position, is input in the increasing order and ends at <00> H. [Caution] When the data, <n> k, is equal to or smaller than its preceding data, <n> k-1, it is assumed that tab setting is finished. If this is the case, the next data onward will be processed as normal data. When the data, <n> k, exceeds a 1-line print area, set the horizontal tab position, assuming "Set digit position = Maximum print digits + 1. " The horizontal tab position does not change even if the character width is altered after setting the horizontal tab position. [Default] · Initial value is specified for each eight characters(9th. 17th. 25th. 33rd columns) of Font A. [See Also] HT [Sample Program] [Print Results] See Sample Program and Print Results for HT on Page 32. [Function] [Code] [Range] 42 CITIZEN CBM-270 User's Manual ESC E n Specifying/Canceling highlighting <1B> H <45> H <n> Specifying/canceling the highlighting characters. [. . . ] Etikettenpapierfehler ----- Tritt auf, wenn Thermalpapier oder nicht-vorschriftsmäßiges Etikettenpapier eingesetzt wird, wenn Etikettenpapier gewählt ist. Die parallele Schnittstelle gibt BUSY und FAULT aus, und die serielle Schnittstelle gibt DTR aus. FEED-Schalter Siehe "4. 6 FEED-Schalterfunktion". 93 CITIZEN CBM-270 User's Manual 4. . 12 Rot/Schwarz-Druck (Vorsichtsmaßregeln) (1) Papiersorten Das rote und schwarze Zweifarb-Thermalpapier ändert seine Farbe durch Steuerung der am Thermalkopf angelegten Energie. Es ist grundsätzlich in zwei Typen unterteilt, entsprechend der Farbentwicklungsreihenfolge. [. . . ]