User manual CITIZEN CBM-262

[. . . ] User's Manual LINE THERMAL PRINTER MODEL CBM-262 Declaration of Conformity Manufacturer's Name : Japan CBM Corporation Manufacturer's Address : CBM Bldg. , 5-68-10, Nakano, Nakano-ku Tokyo, 164-0001, Japan Declare the Product Product Name Model Number(s) Line Thermal Printer CBM-262 Series (CBM-262-R, CBM-262-P) (S. No. 1001001 - ) Conform to the following Standards LVD EMC :EN60950 :EN55022 :EN50082-1 :IEC801-2 :IEC801-3 :IEC801-4 :1992+A1+A2:1993 :1995 Class B :1992 :1991 4KV CD, 8KV AD :1984 3V/m, 27MHz-500MHz :1988 0. 5KV (Signal Line) 1KV (AC Mains) Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the Directive 89/336/EEC, 91/263/EEC, 92/31/EEC, 93/68/EEC" Place: Date: Tokyo, Japan April, 1997 Signature: Full Name: Mikio Moriya Position: General Manager R&D Department European Contact: Norco Declaration AB Box 7146 S-250 07 Helsingborg. Sweden This declaration is applied only for 230V model. Cautions 1. Please read this user's manual thoroughly before attempting to use this printer. [. . . ] Mixed printing with double enlarged characters, and with characters of different sizes, is possible. Character sizes can also be specified by GS !, but the command that is set last is the one that is valid. The initial value is "n = 0". 56 Input Data Format (12) Specifying the absolute print position (ESC $ n1 n2) Code: [1B] h + [24] h + n1 + n2 * (0 n1 FF) (0 n2 3) Data are expressed in Hex code. The next printing start position is specified as an absolute position with the left margin position as the reference. The next printing start position is [(n1 +n2 x 256) x basic calculation pitch] inch from the left margin position. · A specification that exceeds the printing area is disregarded. · If there is a fraction in the calculation results, it is interpolated at the mechanism's minimum pitch. · The horizontal basic calculation pitch (x) is used in the Standard mode. · The following operations are executed in the Page mode according to the starting point. (1) If the starting point is specified as "top left" or "bottom right" by ESC T, an absolute position in a direction perpendicular to the paper feed direction (the character's horizontal direction) is specified. The horizontal basic calculation pitch (x) is used in calculations at this time. (2) If the starting point is specified as "top right" or "bottom left" by ESC T, the absolute position in the paper feed direction (the character's horizontal direction) is specified. The vertical basic calculation pitch (y) is used at this time. (13) Specifying/Clearing the download character set (ESC % n) Code: [1B] h + [25] h + n * (0 n FF) Data are expressed in Hex code. · Download characters and a download bit image (GS *) cannot be defined at the same time. · The initial value is "n0 = 0". 7 57 Chapter 7 Print Control Codes (14) Defining download characters (ESC & s n m a (D1 D2~Dn)) Code: [1B] h + [26] h + s + n + m + a + Dn * (s = 03) (20 n 7E) (20 m 7E) (In the case of Font A, (0 a 0C) (In the case of Font B, (0 a 09) Data are expressed in Hex code. · n indicates the starting character code and m indicates the end character code. · Definable character codes are within the range (20) H ~ (7E) H of ASCII code. · Dn are the defining data and indicate the pattern of "a" dots from the left end in the horizontal direction. · Once it is defined, a download character remains valid until it is redefined, until ESC @ is executed, until GS * is executed or until the power is switched OFF. · It can be known whether characters are downloaded or not by executing ESC v. (In the case of Serial only. ) 7 58 Input Data Format Example · In the case of Font A 12 Dots p1 p4 p7 p34 MSB 24 Dots p2 p5 p35 LSB p3 p6 p36 7 p1=<OF>H p2=<03>H p3=<00>H p4=<30>H p5=<80>H p6=<C0>H p7=<40>H p8=<40>H p9=<20>H . . . . . . 59 Chapter 7 Print Control Codes · In the case of Font B 9 Dots d1 d4 d7 d25 MSB 24 Dots d2 d5 d26 d3 d6 d27 LSB 7 d1 = <03>H d2 = <FF>H d3 = <FF>H d4 = <01>H d5 = <00>H d6 = <20>H d7 = <02>H d8 = <00>H d9 = <10>H . . . [. . . ] In the case of XON/OFF Control: The printer sends the status without confirming if it is possible or impossible for the host computer to receive. · This command is executed during development of the receiving buffer, so if a command is received in accordance with the receiving buffer's state, there is a possibility of a delay occurring while the status is being sent. · If ASB is enabled by GS a, it is necessary to distinguish between the status from this command and the status from ASB. · Paper Sensor Status (n = 1, 31 ) Value 0 Paper present Paper present Paper present Paper present 0 -- -- 0 1 No paper No paper No paper No paper -- -- -- -- Bit 0 1 2 3 4 5 6 7 Printer Status Journal Near End Sensor Status Receipt Near End Sensor Status Journal End Sensor Status Receipt End Sensor Status Not used Not defined Not defined Not used 7 Bits 2, 3: If there is no paper at the end sensors, this printer always goes off-line, so this command is not executed. [. . . ]