User manual CITIZEN CBM-230

[. . . ] LINE THERMAL PRINTER MODEL CBM - 230/231 CBM-230/231 User's Manual Declaration of Conformity Manufacturer's Name : Manufacturer's Address Declare the Product Product Name Model Number(s) : Japan CBM Corporation : CBM Bldg. , 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Thermal Printer CBM-230 Series (CBM230R, CBM230P, CBM231R, CBM231P) (S. No. 95Y0001 ~ ) Conform to the following Standards LVD EMC : EN60950: : EN55022: : EN61000-3-2: : EN50082-1: : IEC801-2: : IEC801-3: : IEC801-4: 1992+A1+A2 : 1993 1994 Class A 1995 1992 1991 4KV CD, 8KV AD 1984 3V/m, 27MHz-500Mhz 1988 0. 5KV Signal Line, 1KV AC mains Supplementary Information "The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336EEC, 92/31/EEC, 93/68EEC" Place Date Tokyo, Japan March, 1998 Full Name: Mikio Moriya Position: General Manager R & D Department Europe Contact : Signature Norco Declaration AB Box 7146 S-250 07 Helsingborg Sweden Warning : This is a Class A products. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This declaration is applied only for 230V model. CITIZEN CBM-230/231 User's Manual IMPORTANT SAFETY INSTRUCTIONS · · · · · · Read all of these instructions and save them for future reference. Slots and openings on the back or bottom of the case are provided for ventilation. [. . . ] The state of the switch(+) can be known through the pin 34 of the interface connector when parallel interface is used, and through the ESC u command when the serial interface is used. (2) Electrical characteristics 1) Drive voltage 2) Drive current 3) Switch signal : DC 24 V : 0. 8 A at maximum(should be within 510 ms) : Signal level "L" = 0 to 0. 5 V "H" = 3 to 5 V (1) Drawer kick drive signal 8. 2 Connector's Pin Configuration No. 1 2 3 4 5 6 Signal Name FG DRAWER 1 DRSW VDR DRAWER 2 GND Function Frame ground Drawer 1 drive signal Drawer switch input Drawer driving power Drawer 2 drive signal Common ground on the circuits Connector used Applicable connector : TM5RJ3-66(HIROSE) : Equivalent to TM3P-66P(HIROSE) [Cautions] 1) No output is allowed during printing. Be careful not to use a drawer with a current over 0. 8A to avoid damage to the printer. ) 8. 3 Drive Circuit 26 CITIZEN CBM-230/231 User's Manual 9. 9. 1 PRINT CONTROL FUNCTION Control Codes List Character 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 HT CR LF ESC SP !% & * ­ 2 3 @ D E G J R c3 c4 c5 d p t v u { V $ ¥ GS k w h H f * / : ^ ESC = a i m Command/Description Horizontal tab command Print command Printing and paper feed Setting the right space amount of the character Specifying collective the print mode Specifying/canceling the download character set Defining the download characters Specifying the bit image mode Specifying/canceling the underline Specifying the 1/6-inch line feed rate Setting the line feed rate n/360 inch Initializing the printer Setting the horizontal tab position Specifying/canceling highlighting Specifying/canceling double printing Printing and feeds the paper n/360 inch Selecting the international characters Selecting the paper near end sensor effective for outputting the paper end signal Selecting the paper near end sensor effective for stopping printing Enabling/disabling the panel switches Printing and feeding the paper by n-lines Generating the specified pulses Selecting the character codes table Transmitting the printer status Transmitting the status of the peripheral device Specifying/canceling the inverted characters Specifying/canceling the 90°- right-turned characters Specifying the absolute position Specifying the relative position Printing the bar code Selecting the horizontal size (scale factor) of the bar code Selecting the height of the bar code Selecting the printing position of the HRI characters Selecting the font of HRI character Defining the download bit image Printing the download bit image Starting/ending the macro definition Executing the macro Data input control Aligning the the characters Full cut Partial cut 27 CITIZEN CBM-230/231 User's Manual 9. 2 Input Data Format (1) Horizontal Tab Command (HT) Code : [09]h Mones the printing position to the next horizontal tab position The horizontal tab position is set by ESC D. The initial setting of the horizontal tab position is every 8 characters (9th columns, 17th columns, 25th columns, 33rd columns, 41st columns) of Font A. (2) Print command (CR) Code : [0D]h 1) When the DIP switch segment DS1-8 is set to OFF This command is ignored. 2) When the DIP switch segment DS 1- 8 is set to ON Printing is done when the internal input buffer has the data. When it has no data, however, line feed is done. (3) Printing paper feed command (LF) Code : [0A]h Prints the data in the internal input buffer and feeds the line(s) based on the set line feed rate. (4) Setting the right space amount of the characters (ESC SP n) Code : [1B]h + [20]h + n * {0 n 20} The data is described with the hexadecimal code. Set the right space of the amount of the character in term of dots (in an increment of 1/203 inch). In the double width magnification mode, the right space amount is double the set amount. 28 CITIZEN CBM-230/231 User's Manual (5) Specifying collectively the print mode (ESC !n) Code : [1Bh] + [21h] + n * {0 n FF} The data is described with the hexadecimal code. Specifies the print mode. Bit 0 1 2 3 4 5 6 7 Function Character font Undefined Undefined Highlighting Vertical double magnification Horizontal double magnification Undefined Underline Value 0 Font A 1 Font B Cancel Cancel Cancel Cancel Specify Specify Specify Specify · Four-fold characters are formed by simultaneously specifying both vertical and horizontal double magnifications. " (6) Specifying/canceling the download character set (ESC % n) Code : [1B]h + [25]h + n * {0 n FF} The data is described with the hexadecimal code. Specifying or cancels the download characters. The download characters and download bit images cannot be defined simultaneously. n0 = 0 : Cancels the download character set n0 = 1 : Specifying the download character set 29 CITIZEN CBM-230/231 User's Manual (7) Defining the download characters (ESC & s n m a {D1 D2 ~ Dn}) Code : [1B]h + [26]h + s + n + m +a + Dn * {s = 03} {20 n 7E} {20 m 7E} {For the Font A; 0 a 0C, For the Font B; 0 a 09} The data is described with the hexadecimal code. Defines the font for the download characters of alphanumeric characters. · "s" denotes the number of bytes in the vertical direction. · "n" denotes a start character code, and m denotes an end character code. · Definable character codes are ASCII codes, totally 95 characters ranging from <20>H to <7E>H. · "a" denotes the numberof dots in the horizontal direction to be derection to be defined. · "Dn" is the data to be defined and denotes a pattern corresponding to "a" dot in the horizontal direction from the left end. · Once the download characters are defined, they remain effective until redefinition, execution of ESC @, execution of GS *, or power -off. 30 CITIZEN CBM-230/231 User's Manual [Example] For the Font A 31 CITIZEN CBM-230/231 User's Manual For the Font B 32 CITIZEN CBM-230/231 User's Manual (8) Specifying the bit Image (ESC * m n1 n2 D1 ~ Dn) Code : [1B]h + [2A]h + m + n1 + n2 + Dn * {m= Bit image mode (refer to the table below)} {0 n1 FF} {0 n2 02} The data is described with the hexadecimal code. Prints the data in the form of bit image in accodance with the bit image mode specified by "m". · The number of bit printed is divided by 256, and n2 and is assumed to be a quotient, and n1 to be the remainder. [. . . ] · Justification listed in the following table is performed depending on the value of "n". n (Hex) Position 0 Left alignment 1 Center alignment 2 Right alignment · Effective only when this is entered at the beginning of the line. · The initial value of "n" is "0". 50 CITIZEN CBM-230/231 User's Manual (41) Full cut (ESC i) Code : [1B]h + [69]h Cuts the paper fully. · Effective only when this is entered at the beginning of the line. [. . . ]