User manual CITIZEN C350

[. . . ] The openings should never be blocked by placing the product on a bed, sofa, rug of other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided. * This product should be operated from the type of power source indicated on the marking label. [. . . ] 19 8. 1 Control Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHARACTER SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 9. 1 Character code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EXTERNAL DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INTRODUCTION The iDP3110 is a dot-impact printer suitable for use with various data communication terminals, and measurement terminals. This product is extremely compact and features extensive functions suited for a wide range of applications. Please read this manual thoroughly to understand the printer before use. Compact desk-top dot matrix printer Light weight High speed printing Low power consumption 1. 2 Accessories The following attachments are included in this set aside from the printer itself. Paper roll Ribbon cassette AC adapter User's manual (1 roll) (1 unit) (1unit) (1 booklet) CITIZEN 1 iDP3110 User's Manual 2. TYPE CLASSIFICATIONS 2. 1 Type The product is categorized according to the naming plan indicated below. iDP3110 24 40 P R J F 120 230 A B iDP3110 24 P J 120 A Model Name Number of columns 24 : 24 columns/144 dots 40 : 40 columns/180 dots Printer cover A : 60mm(Dia. ) Paper roll B : 80mm(Dia. ) Paper roll Power source 120 : AC 120V 230 : AC 220-240V Interface P : Parallel (Centronics) R : Serial (RS-232C) Character J : Japanese F : International 2. 2 AC adapter Please use the exclusive adapter indicated below. Applicable connector (D-Sub connector) Printer : 17LE-13250 (Anphenol equivalent) Cable : 17JE-23250 (Anphenol equivalent) 6. 3 Description of Input / Output Signal (1) I / O signals 1) RD Serial input data signal. Data is ignored when framing error, overrun error, or parity error has occurred. Data input while the signal is BUSY will cause an overrun error to occur and the data will be ignored. Data can be provided to the input buffer even if the printer is printing. Busy state may also occur when power is applied, or during test printing, on-line, or when the printer is reset. CITIZEN 15 iDP3110 User's Manual 3) RESET Signal resets the entire printer. (More than 4ms. ) 4) FG Frame ground 5) GND Common ground for the circuit. (2) Data configuration (1) Start bit (1 bit) (2) Data bit (8 bit) (3) Stop bit (more than 1) CITIZEN 16 iDP3110 User's Manual (3) Electrical characteristics 1) RS-232C circuit Input (RD) [PRINTER] [HOST] MAX 232 equivalent Mark = (-8V) : Stop bit Space = (+8V) : Start bit Output (DTR) MAX 232 equivalent DTR (-8V) when BUSY (+8V) when READY 2) TTL circuit Input (RESET) 7HC14 equivalent Set to LOW when reset CITIZEN 17 iDP3110 User's Manual 7. 1 Character direction selection 2 Baud rate selection 3, 4 Not used 7. 2 Parallel Interface Type Switch Function NO. 1 Character direction selection 2 Print command selection 3, 4 Not used OFF Normal Character CR ON Inverted character LF Shipping Setting OFF OFF OFF OFF Normal character 9600 BPS ON Inverted character 4800 BPS Shipping Setting OFF ON OFF Dip switch position The Arrow mark in the figure below indicates the location of the dip switch with the printer cover removed. Power switch OFF the printer before altering the settings. CITIZEN 18 iDP3110 User's Manual 8. PRINT CONTROL FUNCTION 8. 1 Control Command (1) Print command (CR or LF) In case of initiate parallel transmission, select code CR (0DH) or LF (0AH) on the DIP switch 2. [. . . ] c) International character setting (ESC + R + n) By entering the code ESC + R + n, characters input hereafter are set to the characters for the following countries. n 0 1 2 3 4 Country America France Germany England Denmark n 5 6 7 8 Country Sweden Italy Spain Japan n other than that specified becomes invalid and the setting prior to the invalid specification is employed. When the printer is turned on or RESET, the country is set to n = 0 (America). CITIZEN 22 iDP3110 User's Manual d) Character registration (ESC + & + A1 + A2) Individual patterns can be registered by entering the code ESC + & + A1 + A2, then entering the pattern data. A maximum of 8 characters can be registered, and any address in the range of 20H to FFH can be used for the registration. [. . . ]