User manual CITATION 50 AV CONTROLLER

[. . . ] 5. 0 A/V Controller Owner's Manual ® Staple or clip your original bill of sale here. ¤ 2 Table of Contents Introduction . 59 More on next page 3 Table of Contents (continued) Troubleshooting Guide . Important Information and Setup Instructions For Your New Citation 5. 0 With DTS . 74 Citation is a registered trademark, and Dual Drive and 6-Axis are trademarks of Harman International. [. . . ] Turn the Noise Source back on, and press the ¤ Menu Control button once. Note that the highlight will move to the icon for the front speaker, as indicated by a highlight for that position (Figure OSD-7). Sound Level Calibrat < Spkr Setup Menu Noise Source ON (o) (o) (o +00 +00 +0 (o) +00 (o) +00 (o) +00 Left Front (o) +00 ion < ) 0 (o) +00 Figure OSD-7 In addition, the words Left Front will appear in the middle of the screen, or on the right side of the front panel display. Press the ¤ Menu Control button to advance the active speaker, and note that the sound location will change. If all speakers have been properly connected, the sound will emanate from the speaker location that matches the on-screen display. If all speaker locations match the displays, proceed to the next step. If any position you hear sound from a speaker that DOES NOT match the on-screen indication, press the Menu button three times so that the on-screen displays go out. Turn the 5. 0 off using the Master Power button 1, and turn off all power amplifiers connected to the 5. 0. To correct the mismatch, make certain that the connections are corrected, turn the 5. 0 and the amplifiers back on, and then use the instruction shown above to return to the Sound Level Calibration menu (Figure OSD-6). When all amplifier and speaker connections have been verified, press the ¤ Menu Control button so that the Left Front speaker is highlighted (Figure OSD-7) and use the Volume Controls 8 so that the test noise is at a comfortable level. For more accurate calibration of the system, it is recommended that a sound-pressure level meter be used, and that the first calibration be made to an SPL level of 75dB, at the "C Weighting/Slow" setting on the meter. Note: The use of a properly calibrated SPL meter in setting the output levels is critical in order to achieve the maximum performance from the 5. 0. If you do not have an SPL meter, or are unfamiliar with its use, it is strongly recommended that a trained installer assist with this portion of the system installation. 36 Once the reference level has been set at the Left Front speaker, press the ¤ Menu Control button . The test noise will move to the center speaker, as indicated in the on-screen display. Using the < or > Menu Control buttons , adjust the sound level so that it is equal to the level just set at the Left Front speaker. This may be done either by careful listening or with a sound pressure level meter, but use of the meter is strongly recommended to achieve the most accurate match. It is important that the output level for all channels be made with the < or > Menu . When they are used, you will see the reference offset indication that appears below the speaker position icon change to a positive or negative number. DO NOT use the main system Volume Control to adjust anything other than the Left Front channel when the reference level is being established. Note: System Configuration Control button Once the Center speaker's level has been matched to the reference, press the ¤ Menu Control button again and the test noise will move to the Right Front speaker. Repeat the adjustment procedure as explained above until the output level is equal to the previous two speakers. After adjusting the Right Front speaker, press the ¤ Menu Control button to move to the first available surround speaker. Make the adjustment and continue to use the ¤ Menu Control button to move to each succeeding speaker when complete. After one adjustment of all speakers, including any subwoofers that are connected to the system, repeat the process one more time to double-check that all speakers have an equal output level. Once you are satisfied that all speakers output the test noise at an equal level, press the ¤ Menu Control button until < Spkr Setup Menu < is highlighted at the top of the screen, and press the < Menu Control button to return to the main Speakr Setup menu. [. . . ] 1kHz Subwoofers: 5Hz ­ 100Hz (18dB\Octave) 90dB minimum, A weighted, Ref. 1kHz @ 1 Vrms On-screen programming via remote Two programmable One programmable North America: 120 VAC, 60Hz, 75 watts maximum Export: 230 VAC, 50Hz, 75 watts maximum CE approved Dolby Digital and DTS decoding using leading-edge technology. 6-Axis signal processing first introduced in the Citation 7. 0 creates an enveloping 5. 1-like soundfield from conventional stereo encoded and non-encoded program sources. 4 x 17-1/2 x 15 inches 102 x 445 x 381 mm 21 lbs / 9. 5 kg Specifications Video Inputs Audio Outputs Video Outputs Level/Impedance: Frequency Response: S/N Ratio: Setup/Calibration: Trigger Outputs: Remote IR-Sensor Input: Power Requirements: Decoding: Dimensions (H x W x D): (includes feet and jacks) Weight: 72 Figure Index Operating the Citation 5. 0 is dependent on understanding the meaning of the various on-screen menus, fron panel display messages and other status messages. [. . . ]