User manual CHIEF PLP2053 INS

[. . . ] IMPORTANT: If the installation of this product requires OSHPD seismic approval, refer to OSHPD pre-approval documents and drawings before beginning installation. OSHPD documents and drawings are available at www. chiefmfg. com, and located on the product information page for the mount. BEFORE YOU BEGIN · CAUTION: To prevent damage to your monitor and PLP, which could affect or void the Factory warranty, thoroughly study all instructions and illustrations before you begin to install the mount. Pay particular attention to the Warnings and Cautions in this document. The mount is designed to be installed using wall studs or supporting framework. [. . . ] Parts List REF 10 -- -- DESCRIPTION PLP Series Wall Mount BOLT, Lag, 5/16" x 2 ½" (required, not supplied) WASHER, 5/16" (required, not supplied) QTY 1 4 4 TOOLS REQUIRED FOR INSTALLATION · · Drill and drill bit set Socket wrench set 4 Lag Bolts (Not supplied) NOTE: Other tools may be required depending on your method of installation. 10 4 Washers (Not supplied) Figure 1. PLP Parts 3 Installation Instructions PLP Series PLP INSTALLATION Perform the following procedures to mount the PLP. Select Mounting Location To select the mounting location, do the following: WARNING: It is the responsibility of the installer to verify that the wall to which the mount is anchored will safely support the combined load of all attached components and equipment. Determine the exact mounting location to install the wall mount prior to installation, keeping in mind the screen size. NOTE: Mount the PLP on dual wall studs or some other equivalent supporting framework that is vertical or horizontal. Using a stud sensor, locate the two wood studs where you will mount the PLP as follows: · Refer to Figure 3 for wood studs that are 16" apart on center. Wall Hang the mount on the wall temporarily using a nail in the center hole. Use Triangular Hole to Hang the Mount Wood Studs 16" Pilot Holes OR · Refer to Figure 4 for wood studs that are 24" apart on center. Pilot Holes 3. Using a nail as a temporary hook, hang the mount on the wall using the triangular hole located in the center of the mount (see Figure 2). Use a pencil to mark the mounting holes where the four pilot holes will be drilled into the center of the wood stud. Wood Studs 16"Apart on Center Wood Studs 24" Wall Pilot Holes Pilot Holes Figure 4. Wood Studs 24"Apart on Center 4 Installation Instructions PLP Series PLP INSTALLATION (Cont'd) Mount the PLP To mount the PLP, do the following: 1. Holding the PLP against the wall, select the pair of mounting holes that best suits your situation (see Figures 5, 6, and 7). NOTE: The mounting holes are slotted to allow for a small degree of lateral movement. The mount can be centered, or shifted to the left of center, or right of center depending on stud location. Depending on your situation, install the lag bolts and washers into the pilot holes previously drilled, as described below. Install four 5/16" x 2 ½" lag bolts and four 5/16" washers (two top and two bottom) into the mounting holes, centering the PLP on dual wood studs 16" apart on center as shown in Figure 5. Mounting Holes ­ 16" Apart on Center (Option A) Option B Option A Option C OR · Option B. Install four 5/16" x 2 ½" lag bolts and four 5/16" washers (two top and two bottom) into the mounting holes that are right of center on dual wood studs 16" apart as shown in Figure 6. OR · Option C. Install four 5/16" x 2 ½" lag bolts and four 5/16" washers (two top and two bottom) into the mounting holes that are left of center on dual wood studs 16" apart dual wood studs 16" apart on center as shown in Figure 6. Mounting Holes ­ 16" Apart on Center (Options B and C) OR · Option D. Install four 5/16" x 2 ½" lag bolts and four 5/16" washers (two top and two bottom) into the mounting holes, centering the PLP on dual wood studs 24" apart on center as shown in Figure 7. Option D 3. [. . . ] Over-tightening the nuts may cause excessive wear and may damage your mount. Repeat Steps 1 and 2 until the desired tension is obtained. 15° 0° 1. Return display to desired position. CABLE CONNECTION To installed or removed cables, do the following: 1. Manually tilt the display 0° to 7° up into the service position (see Figure 11). [. . . ]