User manual CHAMBERLAIN WD962KD

[. . . ] 845 Larch Avenue Elmhurst, Illinois 60126-1196 www. chamberlain. com ® GARAGE DOOR OPENER Models WD962KD WD962KLD For Residential Use Only Owner's Manual Please read this manual and the enclosed safety materials carefully!The door WILL NOT CLOSE unless The Protector System® is connected and properly aligned. The model number label is located on the left side panel of your opener. TABLE OF CONTENTS Introduction 2-7 Adjustment 28-30 28 29 30 30 31 31 32 33 33 34 35 36 37 37 37 38 Safety symbol and signal word review. . Operation 31-36 Assembly 8-11 Assemble the rail and install the trolley . [. . . ] · Metal Doors: Drill 3/16" pilot holes and fasten the bracket with the 1/4"-14x5/8" self-threading screws provided. · Wood Doors: Drill 5/16" holes and use 5/16"x2" carriage bolts, lock washers and nuts (not provided) or 5/16"x1-1/2" lag screws (not provided) depending on your installation needs. NOTE: The door bracket may be installed on the top edge of the door if required for your installation. (Refer to the dotted line optional placement drawing. ) HARDWARE SHOWN ACTUAL SIZE Self-Threading Screw 1/4"-14x5/8" Self-Threading Screw 1/4"-14x5/8" Header Wall 2x4 Support Finished Ceiling Door Bracket Top of Door (Inside Garage) Top Edge of Door Header Bracket Optional Placement Door Bracket METAL DOOR Optional Placement of Door Bracket HORIZONTAL AND VERTICAL REINFORCEMENT IS NEEDED FOR LIGHTWEIGHT GARAGE DOORS (FIBERGLASS, ALUMINUM, STEEL, DOORS WITH GLASS PANEL, ETC. ). (NOT PROVIDED) Nut 5/16"-18 Lock Washer 5/16" Top of Door (Inside Garage) Top Edge of Door Optional Placement Carriage Bolt 5/16"x2" (Not Provided) Vertical Centerline of Garage Door Door Bracket For a door with no exposed framing, or for the optional installation, use lag screws 5/16"x1-1/2" (Not Provided) to fasten door bracket. WOOD DOOR 25 INSTALLATION STEP 13 Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated below and on the following page. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the pulley) about 8" (20 cm) (Figures 1, 2 and 3). Figure 1: · Fasten straight door arm section to outer trolley with the 5/16"x1" clevis pin. · Fasten curved section to the door bracket in the same way, using the 5/16"x1-1/4" clevis pin. Figure 3, Hole alignment alternative: · If holes in curved arm are above holes in straight arm, disconnect straight arm. · Find two pairs of holes that line up and join with bolts, lock washers and nuts. Pull the emergency release handle toward the opener at a 45° angle so that the trolley release arm is horizontal. Trolley will re-engage automatically when opener is operated. Pulley 8" (20 cm) min. Trolley Stop Bolt Ring Fastener Inner Trolley Outer Trolley Clevis Pin 5/16"x1" Door Bracket Emergency Release Handle Straight Door Arm Clevis Pin 5/16"x1-1/4" Curved Door Arm Figure 1 Pulley 8" (20 cm) min. Trolley Stop Bolt Lock Washers 5/16" Nuts 5/16"-18 Bolts 5/16"-18x7/8" Door Bracket Figure 2 Pulley 8" (20 cm) min. HARDWARE SHOWN ACTUAL SIZE Trolley Stop Bolt Lock Washers Nuts 5/16" 5/16"-18 Nut 5/16"-18 Lock Washer 5/16" Ring Fastener Clevis Pin 5/16"x1" (Trolley) Clevis Pin 5/16"x1-1/4" (Door Bracket) Hex Bolt 5/16"-18x7/8" Bolts 5/16"-18x7/8" Cut this end Figure 3 26 ALL ONE-PIECE DOORS 1. Assemble the Door Arm: · Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap) (Figure 4). Connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin. · Pull the emergency release handle, disconnecting the outer trolley from the inner trolley by pulling straight down on the emergency release handle and sliding the outer trolley back toward the motor unit. · Connect the curved door arm section to the trolley using the 5/16"x1-1/4" clevis pin and ring fastener. NOTE: Adjusting the limits on the following page: · The trolley will automatically connect. · When setting the up limit on the following page, the door should not have a "backward" slant when fully open as illustrated below. A slight backward slant will cause unnecessary bucking and/or jerking operation as the door is being opened or closed from the fully open position (Figure 5). Figure 4 Door Bracket Ring Fastener Lock Washers 5/16" Clevis Pin 5/16"x1-1/4" Straight Arm Bolts 5/16"-18x7/8 Curved Door Arm Nuts 5/16"-18 Figure 5 Inner Trolley Outer Trolley Door Arm Emergency Release Handle Closed Door Inner Trolley Outer Trolley Correct Angle Open Door Door with Backward Slant (Incorrect) 27 ADJUSTMENT STEP 1 Program the Travel Limits Travel limits regulate the points at which the door will stop when moving up or down. Adjust the position of the door by using the black and purple buttons. Black moves the door UP (open) and purple moves the door DOWN (close). Figure 1 LED Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. [. . . ] To order call: 1-800-528-9131 CLLAD Remote Light Control: Enables homeowner to turn on a lamp, television or other appliance from their car with their garage door opener remote or from anywhere in their home with an additional Chamberlain Security® remote. 41 NOTES 42 NOTES 43 CHAMBERLAIN® SERVICE IS ON CALL OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE. SIMPLY DIAL OUR TOLL FREE NUMBER: HOW TO ORDER REPAIR PARTS Selling prices will be furnished on request, or parts will be shipped at prevailing prices and you will be billed accordingly. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: · PART NUMBER · PART NAME · MODEL NUMBER ADDRESS ORDERS TO: THE CHAMBERLAIN GROUP, INC. Country Club Road Tucson, Arizona 85706 SERVICE INFORMATION TOLL FREE NUMBER: 1-800-528-9131 www. chamberlain-diy. com For professional installation, parts and service, contact your local CHAMBERLAIN® dealer. [. . . ]