User manual CHAMBERLAIN NDIS

[. . . ] While in VOX mode, a call may be initiated by pressing the TALK button. VE ACTI HOLD OFF TALK 1 3 2 4 DOORBELL Call Button: To talk, press and release the Call button and all intercoms in the network will receive the signal. When holding down the Talk button on a different intercom, a secure channel is created and the other intercoms in the network do not hear the conversation. Once a secure link is made, the Call button on the doorbell does not need to be pressed to speak again. MONI TOR ACTIV VOLU ME E TALK 1 2 3 4 CHAN NEL Battery: The AA Alkaline batteries (not provided) will last up to a year depending on use. [. . . ] It may take up to 3-1/2 minutes for a secure network to be established. 3 Press and release the Talk button to verify network is complete. Each intercom will emit a tone when entering programming mode. It may take up to 3-1/2 minutes for a secure network to be established. NOTE: Do not program new intercoms to each other before adding them to the network or they will form a separate network and the memory will need to be cleared. 3 Press and release the Talk button to verify network is complete. HOLD OFF ACTIVE VOLUM E MONIT OR TALK 1 2 3 4 CHA NNEL Operation Talk Button: To talk, hold down the Talk button. All intercoms in the network that are on the same channel will receive the signal. Release the Talk button when done talking and within 10-15 seconds press and hold the Talk button of a different intercom to make a secure channel between the two. Once the channel is made the other intercoms in the network cannot hear the conversation. HOLD OFF ACTIVE VOLU ME TALK MONIT OR 1 3 CHAN 2 NEL 4 Conference Mode: Conference Mode allows multiple intercoms to participate in a conversation 12 compared to Normal Mode in which only two intercoms can communicate. All intercoms must be set to the same channel or the paging channel to be in Conference Mode. Monitor Mode: Monitor Mode is used to monitor the noise in a specific room. Place the intercom in the room that is to be monitored and press the Monitor button until a tone is heard. If a specific channel is selected for Monitor Mode then only other intercoms on that channel or on the paging channel can listen. Monitor mode functions only between base unit intercoms, not with the doorbell unit. HOLD OFF Channel Button: Press the Channel button to set intercom to one of four secure channels or the paging channel. The default channel for the intercom is the paging channel where all four channel lights are lit. An intercom on a channel can only hear an intercom on the same channel or on the paging channel. HOLD OFF ACTIVE VOLU ME TALK MONIT OR 1 3 CHAN 2 NEL 4 Troubleshooting Intercom does not function. Cell phones, cordless phones, or other radio devices may also limit range. D HOL OFF ME VOLU E TAL K 1 OR MONIT 3 2 4 Press the Learn button on the new intercom until a beep is heard. ME VOLU TAL K 1 OR MONIT 3 2 4 HOLD OFF VOLUME MONITOR TALK 1 2 3 4 CHANNEL HOLD OFF ACTIVE VOLUM E MONIT OR TALK 1 2 3 4 CHA NNEL ACTIVE VOLU ME TALK MONIT OR 1 3 CHAN 2 NEL 4 Troubleshooting Intercom beeps every ten minutes. Replace with AA Alkaline batteries or operate it with DC Adapter (not provided). A 12 volt, 300mA DC Adapter may be used (center positive polarity on the round plug). [. . . ] warrants to the first retail purchaser of this product that it is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]