User manual CHAMBERLAIN LA412

[. . . ] LA412 & LA412-S 12 VOLT DC SINGLE SOLAR RESIDENTIAL GATE OPERATOR OW N E R ' S M A N U A L FOR RESIDENTIAL USE ONLY Please read this manual and the enclosed safety materials carefully!Periodic checks of the operator by a qualified technician are required to ensure safe operation. Serial # Installation date 2 YEAR WARRANTY SAFETY TABLE OF CONTENTS Safety Symbol and Signal Word Review Safety Installation Information Gate Construction Information Important Safety Information 1-5 SOLAR PANEL INSTALLATION 1 2 3 4-5 25-28 29-32 29-31 32 32 ADJUSTMENT Limits Force Adjustment Timer-to-Close INTRODUCTION Operator Specifications Carton Inventory Hardware Inventory Additional Items for Purchase Tools Needed 6-7 6 6 7 7 7 PROGRAMMING Remote Controls Keyless Entry Erase All Codes Test 33 33 33 33 33 INSTALLATION Overview of Typical Installation Check Your Gate Mounting Options Manual Release Determine the Position of the Pull-to-Open Bracket Determine the Position of the "Optional" Push-to-Open Bracket Assemble Gate Post Bracket (Pull-to-Open) Attach Brackets to Gate Operator Determine Mounting Location Measuring and Marking for the Gate Bracket Position Gate Operator on Gate Test Gate Travel Secure Post Bracket to Gate Post Secure Gate Bracket to Gate Warning Sign Placement Standard Control Box Large Metal Control Box (XLM) 8-19 8-9 10 10 11 11 11 12 12 13 13 14 15 15 16 16 17-18 19 OPERATION AND MAINTENANCE Reset Button Remote Control Sleep Mode Manual Release Maintenance 34-35 34 34 34 35 35 TROUBLESHOOTING Wiring Diagram Diagnostic Chart Troubleshooting Chart 36-39 36 37 38-39 REPAIR PARTS WIRING Connect the Gate Operator (Gate 1) to the Control Box 20 Set the Lock/Bipart Delay (Model LA412-S Only) 21 Connect the Gate Operator (Gate 2) to the Control Box (Model LA412-S Only) 22 Junction Box (Model LA412-S Only) 23-24 20-24 Control Box Gate Operator Arm How to Order Repair Parts 40-41 40 40 41 WARRANTY POLICY ACCESSORIES TEMPLATE 41 42 BACK COVER SAFETY » SAFETY SYMBOL AND SIGNAL WORD REVIEW When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your gate and/or the gate operator if you do not comply with the cautionary statements that accompany it. [. . . ] NOTE: The system is designed to be charged by either an AC plug-in transformer or a separate solar panel, but not both. Use the cable ties to secure the solar panel cable away from places where it could be damaged. Solar Panel 6 NOTE: If the sky is too overcast to allow the solar panel to power up the system, the panel will need to be verified at another time when the sun is shining. There is no other way to verify the panel installation. P1 C1Ø1 R182 J19 J18 D36 SOL GND MAGR K5 L1 U4 F12 D42 Z1 R2 LOCK ON LEARN XMITTER OFF C75 LOCK / BIPART DELAY C7Ø C71 C72 C73 CONNECT BATTERIES GATE 1 R1 D1Ø BR K2 GR WH YL BL RD F8 The batteries are charged in circuit by using the solar panel (provided). 18 GATE 1 1 2 Connect the plug from the battery to connector on the control board. SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS K1 Z12 Locate the two white battery plugs on the left-hand side of the control box. Battery Connectors Control Board Q9 GATE 2 TIMER RUNNING 24V R1ØØ R9Ø J2Ø BR GR WH R1Ø1 S K4 R186 1 3A 3ØA 32V YL BL D8 K3 D44 OFF MAX C12 OFF MAX RD GATE 2 Q22 D16 F7 Z4 D2 C13 D129 U3 D4 R9 F9 R196 F2 C69 NOTES: Batteries will degrade over time depending on temperature and usage. Batteries do not perform well in extremely cold temperatures. R42Ø R423 JU1 C11 MOV1 D1 R329 R27 J24 F1 J21 F3 AC PW /SOLA K6 J23 30 30 C64 3ØA 3ØA 32V U2 R22 32V JU2 DB1 JU1 2 Board Connectors Battery Connection 28 ADJUSTMENT » LIMITS LIMITS The limits are internal settings that indicate when the gates are in the fully open position and the fully closed position. For proper functionality, the limits must be programmed during the installation process. The specific buttons used for programming depends on which side of the gate the control box is mounted and how many operators the installation includes. Refer to pages 10 and 11 to determine if the gate is Left- or Right-handed. If a mistake is made during programming press the RESET button on the outside of the control box to start over. The programming times-out automatically after 60 seconds of inactivity. 1 Close the gate. 2 Engage the operator by turning the release lever clockwise 180°, then turning the key clockwise 180°. SINGLE ARM LEFT-HAND SIDE OR PROGRAM OPEN SINGLE ARM RIGHT-HAND SIDE PROGRAM OPEN 3 Press the LEARN LIMITS button (SET OPEN LIMIT LED will blink). LEARN LIMITS button 3 Press the LEARN LIMITS button (SET OPEN LIMIT LED will blink). LEARN LIMITS button R2 R1 F3 R2 K2 K2 U4 SET OPEN LIMIT SET EN OPEN T LIMIT Z3 Z4 OFF D9 U3 D4 D4 D1 D2 D2 D6 RESET BUTTON RESET BUTTON the Gate 4 Press button to 1 right move gate to the desired OPEN position. DIAGNOSTIC GATE 1 4 Press the Gate 1 left button to move gate to the desired OPEN position. DIAGNOSTIC GATE 1 SET CLOSE SET CLOSE LIMITS 5 the LEARNbeep. Control board will When gate is in the desired position, press SET OPEN LIMIT SET CLOSE LIMIT is in press 5 When gatebeep. the desired position, Control the LEARN LIMITS button again. board will SET OPEN LIMIT SET CLOSE LIMIT PROGRAM CLOSE 6 Press the Gate 1 left button to PROGRAM CLOSE DIAGNOSTIC move gate to the desired CLOSED position. 6 When the SET CLOSE LIMIT LED blinks, press the Gate 1 right button. DIAGNOSTIC GATE 1 GATE 1 SET CLOSE SET CLOSE gate is in desired closed position, 7 Whenthe LEARNtheLIMITS button again. press SET OPEN LIMIT SET CLOSE LIMIT gate is in desired closed 7 Whenthe LEARNtheLIMITS button. position, press SET OPEN LIMIT SET CLOSE LIMIT The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LEDs stop blinking, programming is now complete. If the problem continues, see Troubleshooting section. ) Test the limits by pressing the SBC to open and close the gate. 29 ADJUSTMENT » LIMITS LIMITS NOTES: · The gate with the longer travel span (opening) must be set as the primary gate (GATE 1). · If one gate is overlapping the other, the gate that is overlapping must be connected to GATE 1 so it will start moving before the other gate; GATE 2 may need to be closed first if there is overlap or a gate lock is being used. · The programming can be exited at any time by pressing the RESET button. Programming times-out automatically after 60 seconds of inactivity. DUAL GATE (LEFT-SIDE PRIMARY OPERATOR) 1 Close the gate. 2 Engage the operator by turning the release lever clockwise 180°, then turning the key clockwise 180°. PROGRAM OPEN the LEARN 3 Presswill blink). LIMITS button (SET OPEN LIMIT LED LEARN LIMITS button R2 K2 U4 SET OPEN LIMIT D4 D2 RESET BUTTON 1 4 Press the GATEopen right button to the left operator. DIAGNOSTIC GATE 1 5 SET CLOSE Press the GATE 2 right button to move the right operator into the OPEN position. SET CLOSE LIMIT LE LIMIT GATE 2 6 Press the LEARN LIMITS button. Control board will beep. SET OPEN LIMIT SET CLOSE LIMIT FORCE PROGRAM CLOSE 7 When the SET CLOSE LIMITS LED blinks, press the GATE 2 left button to close the right operator. SET CLOSE LIMIT LE LIMITS GATE 2 FORCE 8 GATE 1to left button Press the DIAGNOSTIC GATE 1 9 Press the LEARN LIMITS button. SET OPEN LIMIT SET CLOSE LIMIT close the left operator. SET CLOSE The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LEDs stop blinking, programming is now complete. [. . . ] warrants to the first purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of TWO years from the date of purchase. The proper operation of this product is dependent on your compliance with the instructions regarding installation, operation, maintenance and testing. Failure to comply strictly with those instructions will void this limited warranty in its entirety. If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-2806, toll free, before dismantling this product. [. . . ]